Intended Use Of The Product; Technical Data - Hedson IRT UV SMARTCURE Manuel D'instructions

1. Introduction
1.1

Intended use of the product

This product serves exclusively to accelerate the curing
of UV-putty, filler, base and clear coats. The product
must not be used for other purposes than the described
curing processes. The maximum ambient temperature
during operation should not exceed 40°C. The UV LED
equipment is available in wavelengths 365 and 395 nm.
Do not use the product in spray booths or within a
distance of 5 m from other solvent based spraying
activities in order to avoid explosion risks.
Its site of use is the preparation area and finishing
area. Within the automotive industry and vehicle repair
sectors, it is used to cure small areas before polishing.
1.2 UV curing
ed I=4,2A, P=115W, Vega mäter 1090mW => 450mW/cm2 Resterande värde mäter vi relativt detta dvs. (Ocean värdet/25,7)*450 mW/cm/395nm
The ultraviolet light spectrum generated by a UV LED
interacts with special coating chemistries to produce a
high-quality, durable curing. In many applications, UV
curing can achieve a faster curing and therefore also at
a lower total cost. As the UV coat contains less solvent
than conventional paint, the IRT UV SmartCure has less
environmentally impact.
As LED have a narrow wavelength band, it is important
to find the optimal wavelength for each UV putty, filler,
base- and clear coat. IRT offers UV LED equipment in
wavelengths 365 and 395 nm. Please read data sheets
and discuss with the paint suppliers which wavelength is
suitable for your particular product.
Most importantly to achieve a good and fast curing result
there must be enough UV-A intensity. IRT UV radiation has
an outstanding intensity to achieve the best curing result.
Unique benefits of UV cured coating
• Reduced amount of solvent
• Fast curing time
ed I=4,2A, P=115W, Vega mäter 1090mW => 450mW/cm2 Resterande värde mäter vi relativt detta dvs. (Ocean värdet/25,7)*450 mW/cm/395nm
• Low-temperature processing
• Scratch resistant and chemical resistant

2. Technical data

Wavelength nm UV LED
The IRT UV SmartCure is equipped with premium LED
diods emitting UV and visible light with a peak at 365/395
nm. Intensity mW/cm².
Efficiency decreases outside 365/395 nm according to
graphs below.
350 400
4 4
350 400 450
Electrical data
IRT UV
SmartCure
Battery type -
Voltage 18 VDC
Frequency -
Current 8 A
Power 140 W
Noise level <60 dB (A)
Weight - battery
1.16 kg
included
Storage temp.
-20 - +70°C *
Operating temp. -10 - +40°C -10 - +40°C
Wavelength peak 365/395 nm -
Degree of
IP 4X
protection
Classification for
III
indoor use
* Store battery cool. Too much heat will shorten the
service life.
Risk Group EN62471: 3 (RG-3)
Irradiance maps IRT UV SmartCure 365
160 mm
200 mm
Irradiance maps IRT UV SmartCure 395
160 mm
200 mm
EN
Battery Battery
charger
Lithium-ion Lithium-ion
18 VDC 100-240 VAC
- 50-60 Hz
- 2 A
36 Wh / 2 Ah 58 W
- -
- -
-20 - +70°C
-
-
IP 2X IP 2X
II II
Distance 100 mm
Ø 160 mm
Average 185 mW/cm²
Peak 260 mW/cm²
Distance 200 mm
Ø 200 mm
Average 40 mW/cm²
Peak 90 mW/cm²
Distance
100 mm
Ø 160 mm
Average 250 mW/cm²
Peak 350 mW/cm²
Distance 200 mm
Ø 200 mm
Average 50 mW/cm²
Peak 120 mW/cm²
715098 rev 3