Maintenance / Checks; Status Display - Novoferm tormatic T100 R-FU 3kW Mode D'emploi

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

Operating instructions /

Description of function

The control unit allows a variety of operating modes:

Dead man OPEN / dead man CLOSE

Pressing button

and keeping it pressed causes the

door to open until the OPEN end-of-travel position is

reached. Releasing the button causes the door to

stop. The door is closed by dead man's control, i.e.

pressing button

and keeping it pressed, until the

door reaches its CLOSE end-of-travel position. If the

button

is released during closing, the door stops

instantly.

Dead-man operation with key switch only

for access by persons not specifically

instructed.

Impulse OPEN / dead man CLOSE

By briefly pressing the button

impulse from an external impulse generator, the door

starts to open until reaching the OPEN end-of-travel

position or the door can be stopped beforehand by

pressing button . If button

is pressed again, the

door continues to open. The door is closed by dead

man's control, i.e. pressing button

pressed, until the door reaches its CLOSE end-of-

travel position. If the button

closing, the door stops instantly.

Dead-man operation with key switch only

for access by persons not specifically

instructed.

Impulse OPEN / impulse CLOSE

By briefly pressing button

or generating an impulse

from an external impulse generator the door starts to

open until reaching the OPEN end-of-travel position,

or the door can be stopped beforehand by pressing

button . By briefly pressing button

closing until reaching the CLOSE end-of-travel

position.

This operating mode demands that a safety edge

(menu 35) be installed. If the safety edge is triggered

during closing, the door stops and changes direction.

If the safety edge is triggered during opening, this

has no effect. In the case of a defect, the door can be

closed by pressing button .

First impulse:

The operator starts up and causes the door to travel

to the set OPEN or CLOSE travel limits.

Impulse generated during travel:

Door stops.

A new impulse is generated:

Door continues to travel but in the opposite direction.

Fall-back option in the dead man's mode

Should a safety device, such as the closing edge

safety device, the light grid or the light barrier, be

defective, the CLOSE impulse will be deactivated.

The gate can then be closed in the dead man's mode

only. As soon as the faults affecting the sensors have

been rectified, closing in the pulse mode will be

possible again.

• Status display

Display

_______________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

AR-mode / automatic closing

By briefly pressing button

from an external impulse generator, the door starts

opening until reaching the OPEN end-of-travel

position. Or the door was stopped prematurely using

button . After the lapse of the set hold-open time, a

set advance warning time starts running, after which

t h e

g a t e

If button

closing motion of the gate, the AR function

( a u t o m a t i c c l o s e f u n c t i o n ) i s a b o r t e d .

After 20 reversals during the closing motion of the

gate, the AR function is aborted in open position. The

n e x t s t a r t c o m m a n d r e - e n a b l e s i t .

AR-mode with shortened response time via

photocell

Function as described above, but an interruption of

the photocell causes the set hold-open time to be

terminated and the early warning phase to begin.

After the early warning phase has expired, the door

or generating an

automatically closes.

OPEN-CLOSE operation

However, the receiver remains plugged into the drive

in the same operating mode like the one-way control

with the red-green traffic light (optional traffic light

and keeping it

control A800).

Operating sequence for external impulse

is released during

generators:

Generating an impulse in the close position:

Drive starts and moves the door into the open

position

Generating an impulse during the opening:

Door continues to move without being affected

Generating an impulse in the open position:

Door closes

Generating an impulse during the closing:

the door starts

Door stops and opens again

Half-opening of the door

Pressing the ½ button initiates the set half-opening

of the door (menu 32). This function is not available

in dead man's open / dead man's close mode and

also not when a light array is installed.

Lighting and / or early warning light

The control unit has two relay outputs allowing the

switching of lighting or the early warning light (menu

45 and 46).

External command units / impulse generators

The door can be opened and closed via external

command units/impulse generators.

Safety

Connected light barriers and closing edge guards

help avoid accident. The control will only switch to

dead man's c lose mode when it detects a defect.

Key switch function (optional)

The control unit has an input for a key switch. This

allows you to activate the following functions

(menu 50):

Status

Upper end position "Open" reached

Gate end position not reached

Lower end position "Closed" reached

Graphic representation of the gate opening (process sequence)

Graphic representation of the gate closing (process sequence)

Flashing of the inner segments of the segment display: The timer for function „Automatic closing" is active.

or generating an impulse

c l o s e s

a u t o m a t i c a l l y .

is pressed in open position or during the

Input J7 for pulse transducer with Open-

Close switching sequence

Control panel on the control unit is

blocked.

All external control elements are

blocked.

Control panel on the control unit and all

external control elements are blocked.

For 10 secs. the control panel on the

control unit and all the external control

elements are active.

Switching of operating mode to impulse

OPEN / dead man CLOSE.

Switch to half opening of the door.

Input J7 for pulse transducer with Open-

Stop-Close

Input J7 for pulse transducer with Half

Open-Close

AR-mode / automatic closing

RWA (smoke-heat exhaust) function

The RWA position is actuated

compulsorily when this function is

triggered. To restart the control, a

network reset must be performed.

like 10, but inverted entry

mutual gate locking

Radio hand transmitter (optional)

Button: Start

½ button for half-opening:

Pulse, AR and open-close modes can be set for both

keys (menu 68).

Function as with the START button, but the door

travels to the set half-open position only.

Button: Light

The light function involves a continuous light that can

be switched on/off independent of the door action.