Scheppach MIX125 Traduction Des Instructions D'origine page 17

7. Installing lockwasher Fig.9
Install lockwasher (13) with 2 M8x25 hexagon
bolts, 2 washers, 2 lockwashers on the swivel
axis and tighten.
8. Installing swivel wheel. Fig.10
Insert the spring with the washer on the top into
the sleeve on the tipping wheel. Slide the wheel
over the larger diameter shaft until the holes in
Operate the concrete mixer only if no parts
(e.g., safety covers) are missing or defective,
and the connecting cable is not damaged.
Set up:
•
Place the concrete mixer horizontally on even,
firm ground.
•
Do not place it on the connecting cable!
•
Route the connecting cable in a manner, such
that it cannot be kinked, crushed or damaged
in some other way.
Note:
It should be possible to swivel the drum to
the right and left. There must be sufficient
Caution!
Pull the power plug out, every time, before trans-
porting the machine.
1. Set the filling opening downwards.
Caution!
While working with the concrete mixer or per-
forming repairs on it, please do the following:
Switch off the concrete mixer, wait for the drum
to come to a standstill and pull out the power
plug.
Repairs on the concrete mixer should be per-
formed only by authorised technicians.
Caution! Switch off the machine, wait for the
drum to come to a standstill and pull out the
power plug.
Caution! Switch off the machine, wait for the
drum to come to a standstill and pull out the
power plug.
•
Remove the cover of the motor casing, check
Fault
Motor switches off
Motor runs, drum does not move
Switch off the concrete mixer if such faults occur, pull out the power plug and get the fault rectified by an authorised professional company
the braket line up with the hole drilled. Insert a
M10X65 hex bolt with a flat washer and screw
on a nut with a flat washer from the other side.
Screw the nut up against the bracket firmly, but
not so tightly so as to prevent the wheel from piv-
oting about the bolt. Tighten the M10X30 socket
head cap screw on the sleeve to adjust the spring
tension.
Operation
space for a wheelbarrow under the drum, so
that it can be emptied.
Activation:
•
Plug the device into the socket Activation on
"I" (green button) / Deactivation on "0" (red
button)
Moving the drum (Fig. 12):
•
To move the drum, pull back the hand wheel so
that the drum can be moved.
•
When the drum is in the desired position, lock
the hand wheel again.
Transport
2. During transportation by motor vehicle, re-
move the screws and fold the stands.
3. Lock the mixer with a strap to prevent displace-
ment
Maintenance
Perform visual inspection before each use of the
concrete mixer.
All safety parts must be installed.
Defective connecting cables should not be used.
Service information
Please note that the following parts of this prod-
uct are subject to normal or natural wear and that
Cleaning
Clean the drum with water after each use of the
concrete mixer.
Checking/re- adjusting belt tension
the belt tension (on pressing the belt with the
finger, it should yield by approx. 5mm.)
•
Belts are wear and tear parts that must be
replaced after a certain period. If necessary,
Troubleshooting
Possible cause
Motor is overloaded
V-belt skids through
Remedy
Let motor cool down
Replace V-belt
17
Note: The wheel must be allowed to pivot about
the bolt so that the lugs on the bracket can be
engaged or disengaged from the slots in the lock-
ing plate.
9. Installing motor casing. Fig.11
Place the motor casing on the retaining plate, se-
cure with 4 M8 safety nuts and flat washers.
Filling
• Before filling the drum, ensure that the opening
is aligned in such a way that the mixture cannot
fall out of the drum. (Fig. 13)
•
Put the mixture in when the drum is rotating
(do not overfill the drum)
Caution! Risk of moving parts
Emptying
•
Swivel the drum in the downward direction to
empty it
•
Ensure that there is an adequate container un-
der the drum (e.g., wheelbarrow).
•
Ensure that no mixture falls on the ground
4. Do not lift the concrete mixer with the help of
a crane
the following parts are therefore also required for
use as consumables.
Wear parts*: V-belts
* Not necessarily included in the scope of deliv-
ery!
Remove cement and mortar residues. Do not tap
motor casing and drum with a shovel or any other
hard object, as these can be damaged.
detach the screws on the motor, replace the
belt, adjust the correct tension and tighten the
screws again.
•
Reinstall the motor cover.
D GB