Technical Characteristics - Bras B-EXPRESS 20.2 Carnet D'instructions

EN GLIS H
B - E X P R E S S

1 TECHNICAL CHARACTERISTICS

Number of powder containers
Capacity of each container, approx.
Capacity of water tank, approx
Dimensions:
width
depth
height
Net weight, approx.
Gross weight, approx.
Noise level below 70 dB(A).
IMPORTANT
Electrical characteristics: read the data featured on the
data plate of each dispenser; this data plate is situated at
the bottom of the compartment of the water tank. The
serial number of the appliance (preceded by the symbol
#) is given on the same data plate.
Specifications are subject to change without notice.
2 INTRODUCTION
Please read all sections of this manual thoroughly to familiarize
yourself with all aspects of the unit.
Like all mechanical products, this machine will require cleaning
and maintenance. Besides, dispenser working can be
compromised by operator's mistakes during disassembly and
cleaning. It is strongly recommended that personnel responsible
for the equipment's daily operations, disassembly, cleaning,
sanitizing and assembly, go through these procedures in order
t o b e p r o p e r l y t r a i n e d a n d t o m a k e s u r e t h a t n o
misunderstandings exist.
3 INSTALLATION
1 Take the dispenser out of its packaging, which we
recommend you keep for future requirements.
2 Make sure that the dispenser has not been damaged during
transportation. If this is the case, immediately make a claim
with the forwarder.
3 Place the dispenser onto a counter designed to withstand
its weight, including when full.
4 Before making the electrical connection to the dispenser,
check that the supply mains matches the one specified on the
data plate. Connect the dispenser to a single-phase network,
using an earthed socket as set forth by the applicable
regulations in force. If the dispenser is supplied without a plug,
connect to the cable a plug that is compliant with the standards
in force in your country, has an earth pin or contacts, and is
suitable for currents of at least 10 A 250 V (for areas with
voltages of 220-230 V 50-60 Hz) or 20 A 250 V (for areas with
voltages of 100-115 V 50-60 Hz). Should you wish to make a
fixed connection to the network, connect the cable to a bipolar
wall switch with a minimum contact opening of 3 mm. Do not
use extensions for the electrical connection of the appliance.
Make sure the appliance is earthed correctly; if this is not
the case, this may cause electric shocks to people or
damage to the dispenser.
n 1 2
cc 1000 1000
5 The unit doesn't come pre sanitized from the factory. Before
cc 4500 4500
serving products, the dispenser must be disassembled,
cleaned and sanitized according to this handbook instructions
( s e e p a r a g r a p h 6 C L E A N I N G A N D S A N I T I Z I N G
cm 19 27
PROCEDURES).
cm 39 39
cm 52 52
kg 20 25
Install
kg 22 27
accessible.
4 TO OPERATE SAFELY
1 Do not operate the dispenser without reading this
operator's manual.
2 Do not operate the dispenser unless it is properly
grounded.
3 Do not use extension cords to connect the dispenser.
4 Do not operate the dispenser unless all panels and covers
are restrained with screws.
5 Do not put objects or fingers in panels louvers and faucet
outlet.
6 Connect the device to a system with a nominal voltage of
230V and a maximum impedance of Zmax = 0.34 Ω.
7 For best results, use only powders specially prepared for
freeze - dried produ cts an d foll ow the man ufactu r er' s
instructions.
5 OPERATING PROCEDURES
5. 1 DISPENSER SET UP
1 Before use, clean and sanitise the dispenser according to
the instructions provided herein (see chapter 6 CLEANING).
2 Remove the drip tray (1) and the product dispensing
10
ATTENTION
IMPORTANT
the dispenser so that the plug is easily