Inspection And Service; Ec Declaration Of Conformity; Technical Data; Np1 - EUCHNER NP Serie Mode D'emploi

Operating Instructions
Safety Switches NP...
Proceed as follows:
Mechanical function test
The actuator must slide easily into the actuating
head. Close the safety guard several times to check
the function.
Electrical function test
1. Switch on operating voltage.
2. Close all safety guards.
The machine must not start automatically.
¨ ¨
3. Start the machine function.
4. Open the safety guard.
The machine must switch off and it must not be
¨ ¨
possible to start it as long as the safety guard
is open.
Repeat steps 2 - 4 for each safety guard.

Inspection and service

WARNING
Danger of severe injuries due to the loss of the
safety function.
If damage or wear is found, the complete switch
f
and actuator assembly must be replaced. Re-
placement of individual parts or assemblies is
not permitted.
Check the device for proper function at regular
f
intervals and after every fault. For informa-
tion about possible time intervals, refer to
EN ISO 14119:2013, section 8.2.
Inspection of the following is necessary to ensure
trouble-free long-term operation:
correct switching function
f
secure mounting of all components
f
damage, heavy contamination, dirt and wear
f
sealing of cable entry
f
loose cable connections or plug connectors.
f
Information: The year of manufacture can be seen
in the bottom, right corner of the type label.
Exclusion of liability and warranty
In case of failure to comply with the conditions for
correct use stated above, or if the safety instruc-
tions are not followed, or if any servicing is not
performed as required, liability will be excluded and
the warranty void.
Notes about
The following information applies to devices
with cable entry:
For use and applications as per the requirements
of , a copper wire for the temperature range
60/75 °C is to be used.
The following information applies to devices
with plug connector:
For use and applications as per the requirements of
, a class 2 power supply according to UL1310
must be used. Connection cables for safety switches
installed at the place of use must be separated
from all moving and permanently installed cables
and un-insulated active elements of other parts
of the system which operate at a voltage of over
150 V. A constant clearance of 50.8 mm must be
maintained. This does not apply if the moving cables
are equipped with suitable insulation materials which
possess an identical or higher dielectric strength
compared to the other relevant parts of the system.

EC declaration of conformity

The manufacturer named below herewith declares
that the product fulfills the provisions of the direc-
tive(s) listed below and that the related standards
have been applied.
EUCHNER GmbH + Co. KG
Kohlhammerstr. 16
D-70771 Leinfelden-Echterdingen
Directives applied:
Machinery directive 2006/42/EC
f
Standards applied:
EN 60947-5-1:2004 + Cor.:2005 + A1:2009
f
EN 1088:1995+A2:2008
f
EN 14119:2013
f
The original EC declaration of conformity can also
be found at: www.euchner.de
Service
If service support is required, please contact:
EUCHNER GmbH + Co. KG
Kohlhammerstraße 16
D-70771 Leinfelden-Echterdingen
Service telephone:
+49 711 7597-500
Fax:
+49 711 753316
E-mail:
support@euchner.de
Internet:
www.euchner.de
5

Technical data

Parameter Value
Housing material Reinforced thermoplastic
Degree of protection acc. to
IEC 60529
NP1... (cable entry) IP67
NP2... (plug connector SR6) IP65
NP3... (plug connector SM4) IP67
Mech. life 1 x 10 operating cycles
6
Ambient temperature
NP1.../NP2... -20 ... +80 °C
-20 ... +60 °C
NP3...
Degree of contamination
3 (industrial)
(external, acc. to EN 60947-1)
Installation position Any
Approach speed, max. 20 m/min
Extraction force 15 N
Retention force 2 N
Actuating force, max. 5 N
Actuation frequency 6700/h
Switching principle Slow-action switching contact
Contact material Silver alloy
Connection

NP1...

Cable entry M20 x 1.5
NP2... Plug connector SR6, 6-pin+PE
NP3... Plug connector SM4, 4-pin
Conductor cross-section
(flexible/rigid)
NP1... 0.34 ... 1.5 mm²
Conditional short-circuit
100 A
current
Switching voltage, min., 24 V
Switching current, min., at 24 V 30 mA
Short circuit protection (control circuit fuse) acc. to IEC 60269-1
NP1.../NP2... 4 A gG
NP3... 2 A gG
Conventional thermal cur-
rent I
th
NP1.../NP2... 4 A
NP3... 2 A
Utilization category acc. to
NP1.../NP2...
EN 60947-5-1
AC-15 4 A 230 V
DC-13 4 A 24 V
Rated insulation voltage U = 250 V
i
Rated impulse withstand
U = 2.5 kV
voltage imp
Limitations for version NP2 with ambient temperatures
>70 °C
Utilization category acc. to EN 60947-5-1
AC-15 2 A 230 V
DC-13 2 A 24 V
Conventional thermal cur-
2A
rent I
th
Short circuit protection
(control circuit fuse) acc. to 2 A gG
IEC 60269-1
Reliability values acc. to EN ISO 13849-1
B 3 x 10
6
10d
NP3...
1.5 A 230 V
1.5 A 24 V