Service And Maintenance Instructions; Troubleshooting; Technical Data; Putting Out Of Operation/Waste Disposal - Uponor UP 110 Mode D'emploi

Instruction Manual
UP110
4.4 Service and maintenance instruction
The reliable performance of the tool is dependent on ca-
reful treatment and service. This represents an important
condition to safeguard a lasting connection. To safeguard
this the tool have to be maintained and serviced regularly
We would like to draw your attention to the following
points:
1. The electric-hydraulic pressing unit have to be cleaned
and dried after each use before being put into the trans-
portation case.
2. In order to guaranty a proper function of the machine
the pressing tool should be returned to the manufac-
turer or one of our Authorized Service Centers (ASC)
after the light diode display indicates Service or after
each year whatever comes fi rst.
3. The battery as well as the charging unit must be protec-
ted against humidity and foreign objects.
4. The bolt joins, the rollers and their guides must be oiled
regularly in small amounts.
5. Check through test crimps or have the tool manufactu-
rer check the tool and pressing jaws regularly for proper
function.
6. Keep pressing jaws clean. Remove dirt with a brush.
In order to avoid possible malfunctions we offer you a ma-
nufacturer service consisting of disassembly, cleaning,
exchange of possibly worn out parts assembly and fi nal
control (see ASC). Only a clean and properly functioning
press system can over the time safeguard a leaking free
connection.
Within the determined use of the tool only the pressing
jaws are permitted to be changed by the customers.
Attention
Do not damage the seals of the tool. If the seals
are damaged the warranty is invalidated.
5.

Troubleshooting

a.) Constant fl ashing/indicating of the light diode display
or the occurence of an acoustical warning signal.
 see table 1. If the failure can not be solved return the
tool to the nearest service center (ASC).
b.) The tool loses oil.
 R eturn the unit to the manufacturer. Do not open it and
damage the seal of the tool.
c.) The red LED fl ashes 3X and simultaneously 3
acoustic warning signals occure (see table 1).
 S erious fault! If this fault occures repeatedly return the
unit to an Autorized Service Center (ASC). Do not open
it and damage the seal of the tool.
In case of a one time occurence the fi tting has to be
dismantled or pressed a second time.
HE.15875 - UP110 - 01/2015

6. Technical Data

Weight 3,5 kg
(incl. battery):
Thrust force (linear): 32 kN min.
Driving motor: direct-current permanent fi eld
Battery voltage: 18 V DC
Battery capacity: 3 Ah (1083608)
Charging time: 22 min. (1083608)
Pressing time: 4s to 7s (depending on the
nominal width)
Pressing approx. 300 compressions/
performance: battery with NW 20
Hydraulic oil: Rivolta S.B.H. 11
Environmental tem- -10°C bis +40°C
perature:
Sound level: 70 dB (A) in 1m distance
Vibrations: < 2,5 m/s²
Dimensions: See page II, pic. 2
7. Putting out of operation/waste
disposal
This unit is subjected to the scope of the European WEEE
(2012/19/EU) and RoHS (2011/65/EU) directives.
Information about this can be found on our home page
www.Klauke.com under 'WEEE & RoHS'.
Battery cartridges (page I, pic. 1, 3) must be specially dis-
posed of according to the EEC Battery Guideline.
Attention
Do not dispose of the unit in your residential
waste. Klauke has no legal obligation to take
care of their WEEE outside Germany unless the
product has been shipped and invoiced from
inside your country by Klauke. Please contact
your distributer to fi nd out more how to get your
tool recycled environmentally friendly.
Note
Additional copies of the of the IM are available
upon request with no charge:
www.uponor.com
made by
GB
3