Uponor UP 110 Mode D'emploi page 11

Instruction Manual
UP110
Index
1. Introduction
2. Warranty
3. Description of the electric hydraulic
pressing unit
3.1 Components of the unit
3.2 Brief description of the important features
of the unit
4. Remarks in respect of the determined use
4.1 Operation of the unit
4.2 Explanation of the application range
4.3 Mounting instructions
4.4 Service and maintenance instructions
5. Troubleshooting
6. Technical data
7. Putting out of operation/waste disposal
Symbols
Safety warnings
Please do not disregard these instructions in or-
der to avoid human injuries and environmental
damages.
Operational warnings
Please do not disregard them to avoid dama-
ging the unit.
1. Introduction
Before starting to use the tool please read
the instruction manual carefully.
Use this tool exclusively for its determined use respec-
ting the all international and domestic health and safety
regulations.
Use this tool exclusively for its determined use.
This instruction manual has to be carried along during the
entire life span of that tool.
The operator has
• to guarantee the availability of the instruction manual
for
the user and
• to make sure, that the user has read and understood
the instruction manual.
2. Warranty
Regardless of the warranty with your direct sales cont-
ract partner we can accept liability claims due to material
defects up to 24 months from our delivery date or up to
10,000 tool cycles, whichever comes sooner. Conditions
of our liability are contingent upon proper tool operation
and compliance with the required periodic maintenance
of the tool through the tool service center. Our warranty
policy accounts for the exchange or repair of defective
tools. Further claims will not be realized when we are not
the direct sales contract partner.
HE.15875 - UP110 - 01/2015
3. Description of the universal
pressing unit
3.1 Components of the unit
The electric-hydraulic tool is hand guided and consists of
the following components:
Tab. 2 (see pic. 1)
Pos. Description Function
1 LED (red) Indicator for battery charge
control, tool functions and
faults
2 Retract slide slide to retract the drive rolls in
case of an error or emergency
3 Battery rechargeable 3 Ah Li-Ion
cartridge battery (1083608)
4 Trigger operating switch
to start the motor
5 LED (white) to illuminate the working area
6 Pin bolt to lock the pressing jaws
7 Pressing jaws dies to press the fi tting on the
pipes (will be supplied by the
system provider)
8 Pressing head reception for the pressing
jaws, respectively press chains
9 Housing ergonomically formed plastic
housing in a 2-Component
design for perfect handling
3.2 Brief description of the important
features of the unit
Safety features:
The unit is equipped with a special brake which in-
stantly stops the forward motion of the piston/dies
when the trigger is released.
A white LED illuminates the working space after
activating the trigger. It automatically switches off
10 sec. after releasing the trigger. This feature can
be deactivated.
Hydraulic Pressure Check, HPC for short, monitors
the oil pressure in the tool's oil circuit, hence ensur-
ing a continuous, consistent press quality.
During each pressing cycle, the achieved pressing
pressure is determined by a pressure sensor and
compared to the required minimum value. An audi-
ble warning signal sounds if the achieved pressure
differs from the specified working pressure. The
user will know immediately that the fi tting must be
checked and repressed or replaced as required.
Functional features:
The unit is equipped with a double piston pump
which is characterised by a rapid approach of the
dies towards the connector.
The hydraulic unit incorporates an automatic retrac-
tion which returns the piston into its starting position
when the maximum operating pressure is reached.
A manual retraction allows the user to return the pis-
ton into the starting position in case of an incorrect
crimp.
The crimping head can be smoothly turned by 350°
around the longitudinal axis in order to gain better
access to tight corners and other diffi cult working
areas.
made by
GB
1