Technical Data - EINHELL TC-SM 2534/1 Dual Instructions D'origine

4. Technical data

AC motor: .................................230-240 V~ 50Hz
Power: ................... 2100 W S1 / 2350 W S6 25%
Idle speed n : ......................................4000 min
0
Carbide saw blade: ...........ø 250 x ø 30 x 3.0 mm
Maximum tooth pitch: .............................. 3.2 mm
Number of teeth: ............................................ 48
Swiveling range: ........................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Miter cut to the right: ...............................0° to 45°
Saw width at 90°: ............................ 340 x 75 mm
Saw width at 45°: ............................ 240 x 75 mm
Saw width at 2 x 45°
(double miter cut left): ...................... 240 x 42 mm
Saw width at 2 x 45°
(double miter cut right): ................... 240 x 25 mm
Weight: .......................................... approx. 16 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class: ........................................... II/
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 180 mm.
Operating mode S6 25%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 25% of the cycle at the
specifi ed rating and must then be allowed to idle
for 75% of the cycle.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
Operation
L sound pressure level ........................ 96 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ........................ 109 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Anl_TC_SM_2534_1_Dual_SPK9.indb 25 Anl_TC_SM_2534_1_Dual_SPK9.indb 25
GB
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
-1
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
- 25 -
10.12.2019 13:23:48 10.12.2019 13:23:48