Technical Data; Initial Operation - Bosch Active Line Notice Originale

OBJ_BUCH-2616-002.book Page 2 Thursday, May 12, 2016 12:37 PM
English–2
14 Increase assistance level button
15 Button push/start aid "WALK"
16 Lock latch for on-board computer
17 Locking screw for on-board computer
USB charging cable (Micro A – Micro B)*
* not illustrated; available as accessory

Technical Data

On-board computer
Article number
Internal memory in total
1 270 020 907
1 270 020 915
Max. charging current,
USB connection
Charging voltage,
USB connection
1)
USB charging cable
Operating temperature
Storage temperature
Charging temperature
Internal lithium-ion battery
2)
Protection type
Supported wi-fi standards
Weight, approx.
1) Not included as part of standard delivery
2) When USB cover is closed
Assembly
Inserting and removing the on-board computer
(see figure A)
To insert the on-board computer 3, slide it from the front into
the holder 4.
To remove the on-board computer 3, press the lock latch 16
and slide the on-board computer toward the front out of the
holder 4.
 Remove the on-board computer when you park the
eBike.
It is possible to secure the on-board computer against
removal in the holder. To do so, remove the holder 4 from the
handlebar. Put the on-board computer in the holder. Screw
the locking screw 17 (thread M3, 8 mm long) from below into
the thread provided in the holder. Mount the holder back onto
the handlebar.
1 270 020 XBN | (12.5.16)
Nyon
1 270 020 907/915
GB 1
GB 8
mA 500
V 5
1 270 016 360
°C –5...+40
°C –10...+50
°C 0...+40
V 3.7
mAh 710
IP x7 (watertight)
802.11b/g/n
(2.4 GHz)
kg 0.2
Operation

Initial Operation

Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged eBike battery pack is inserted (see
operating instructions of the battery pack).
– The on-board computer is properly inserted in the holder
(see "Inserting and removing the on-board computer",
page English–2).
Switching the eBike System On/Off
Options for switching on the eBike system:
– Place the on-board computer into the holder 4.
– When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button 5 of the on-
board computer.
– When the on-board computer is inserted, press the On/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
The drive is activated as soon as you step on the pedals (ex-
cept for in the push assistance function or in assistance level
"OFF"). The motor output depends on the settings of the as-
sistance level on the on-board computer.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25/45 km/h, the assis-
tance from the eBike drive is switched off. The drive is auto-
matically re-activated as soon you start pedaling again and the
speed is below 25/45 km/h.
Options for switching off the eBike system:
– Press the On/Off button 5 of the on-board computer for at
least 1 second.
– Switch the eBike battery pack off by its On/Off button (see
battery pack operating instructions).
– Remove the on-board computer out of its holder.
If no power is drawn from the drive for about 10 minutes (e.g.
because the eBike is not moving) or no button is pressed on
the Nyon, the eBike system will shut down automatically to
save energy.
Bosch eBike Systems
O