Kärcher B 40 C Bp Mode D'emploi page 11

Clean water distribution channel
 Remove the rubber strip and clean the
channel with a cloth. After cleaning, re-
place the rubber strip evenly.
Replacing the brush rollers
 Lift the cleaning head.
1 Unlocking key, storage cover
2 Brush
3 Push button
 Press the release button of the storage
cover.
 Swivel the storage cover to the side.
 Pull out the brush rollers.
Note: The brush rollers must be re-
placed when the bristle length has
reached 10 mm.
 Insert new brush rollers.
 Swivel the storage cover back and
press it closed on the pushbutton.
Replacing the disk brushes
 Lift the cleaning head.
 Press the pedal for changing the brush-
es downward beyond its resistance.
 Pull the disc brush out of the side below
the cleaning head.
 Hold the new disc brush under the
cleaning head, push upward and lock.
Install cleaning head
 Push the appliance forward about 2 m
so that the steering rollers point toward
the rear.
 Press the pedal for lowering the clean-
ing head downwards slightly and then
move it to the left. This unlocks the ped-
al. Release the pedal slowly upwards.
The lift arm of the cleaning head will be
lowered.
 Empty the solution and recovery tank .
 Loosen the tank lock and tilt the tank
upwards.
1
1 Spring element
2 Locking pin
2
3 Terminal strip cover
4 Lock of safety pin
3
 Place the cleaning head halfway in front
of the appliance.
 Remove the terminal strip cover.
 Connect the mains supply cable of the
cleaning head to the appliance.
 Attach the terminal strip cover.
 Connect the hose couplers on the
cleaning head to the hose on the appli-
ance.
1 Spring element
2 Push handle
 Insert the push bow into the cleaning
head intake.
 Push the spring elements down and lock
them into place.
 Align the lift arm of the cleaning head with
the intake on the top side of the cleaning
head.
 Insert the safety pin and lock it into
place.
 Adjust the cleaning head: to the de-
sired position via the adjustment screw.
 Swivel the water reservoir all the way
down, check the lock.
Dismantling the cleaning head
The removal will take place in the opposite
order of the installation.
CAUTION
When the cleaning head is removed, the
stability of the appliance can be compro-
mised; ensure a safe stance.
Possibly support the rear to prevent tipping.
9
-
US
Batteries
Please observe the following warning notes
when handling batteries:
Observe the directions on the bat-
tery, in the instructions for use
and in the vehicle operating in-
structions
Wear eye protection
Keep children away from acid and
batteries
Danger of explosion
Fire, sparks, naked flames and
smoking must be strictly avoided
Danger of chemical burns
First aid
Warning note
Disposal
Do not throw the battery into the
regular waste
Danger
Danger of explosion. Do not put tools or
other objects on the battery, i.e. on the ter-
minal poles and cell connectors.
Risk of injury. Ensure that wounds never
come into contact with lead. Always clean
your hands after having worked with batter-
ies.
Recommended batteries, B 40
Order No. Description
6.654-141.0 105 Ah - mainte-
1)
nance-free
6.654-093.0 70 Ah - maintenance-
2)
free
6.654-097.0 80 Ah, - low mainte-
3)
nance
* Appliance requires 2 batteries
Complete set (24 V/105 Ah) incl. connect-
1)
ing cable, order no. 4.035-449.0
Complete set (24 V/70 Ah) incl. connect-
2)
ing cable, order no. 4.035-447.0
Complete set (24 V/80 Ah) incl. connect-
3)
ing cable, order no. 4.035-450.0
12 V*
12 V*
12 V*
11