Commands And Functions - dB Technologies FLEXSYS FM Série Mode D'emploi

FLEXSYS FM 12
The FLEXSYS FM 12 active coaxial stage monitor is
equipped with digital amplifier delivering 240W RMS for
the bass section and 60W RMS for the high frequency
section.
The speaker is equipped with 12" coaxial woofer (2" voice
coil) and 1" Neodymium driver (1,3" voice coil) loaded with
asymmetric 60°x90° horn.
The speaker is made with hybrid technology H.E.T.
(Hybrid Enclosure Technology): box made in lighter
plywood PVC coated, sides in polypropilene , and is
provided with a handle, on bottom side, which eases
transportation.
In the left side of box there is a standard pole mount cup
(D36mm).
FLEXSYS FM8,FM10,FM12
REFLEX HOLES
AMPLIFIER
7
HANDLE
O 36mm PEDESTAL/
DRIVER WOOFER
BRACKET HOUSING

COMMANDS AND FUNCTIONS

AMPLIFIER PANEL (Ref. page 22)
1) " BALANCED INPUT" (XLR), " LINK" (XLR/JACK 6,3mm) CONNECTORS
These balanced inputs can be used to connect balanced or unbalanced
microphones or audio sources at line level (0dB) (eg. preamplifier, mixer, recorder,
CD player, musical instrument, ...).
The balanced connector is connected in parallel and can be used to send the audio
signal to other amplified speakers, recorders or supplementary amplifiers.
2) "LIMITER" INDICATOR LIGHT
This indicator shows red to indicate that the internal limiter circuit has tripped.
This prevents amplifier distortion and protects the speakers against overloads.
3) "ON SIGNAL" INDICATOR LIGHT
This indicator light comes on green to indicate that the amplifier is switched on and it
is working properly. The "ON SIGNAL" green LED flashes slowly, when there is
signal absence. During normal operation the LED serves as Vu-meter monitoring
the audio level riproduced.
4) "SENSITIVITY" CONTROL
The knob regulates the speaker´s volume.
This control does not affect the output "LINK" levels.
5) "INPUT SENS" SWITCH
Position the switch in LINE to use a line level source (0 dB) or MIC to use a
microphone.
6) EQUALIZATION "DSP SETUP" SELECTOR
This control enables to select the suitable equalization for loudspeaker use.
It is possible to select one of 8 different presets:
1 - LIVE MONITOR.
For use during live performances with the loudspeaker positioned as monitor.
recommended for musicians and singers.
2 - PLAYBACK MONITOR.
For musical playback (MP3 players, CDs, etc.), even in a live location with
loudspeaker in monitor position. Low and high frequencies are emphasized.
3 - COUPLED MONITORS.
For use of multiple loudspeakers side by side. The coupling effect of the
loudspeakers is optimized.
4 - MALE SINGER.
Designed for male voices since it emphasizes the medium-low frequencies,
minimizing the feedback of the low frequencies.
5 - FEMALE SINGER.
Designed for female voices since it emphasizes the medium-high frequencies,
giving the voices a sharp effect. The feedback is strongly limited.
6 - ANTIFEEDBACK.
Specifically designed for cardioid and hypercardioid microphones. It significantly
minimizes the feedback due to the proximity effect, both on low and high
frequencies.
7 - LIVE ON STAND.
Suitable for loudspeakers located on stands, optimized for live performance.
8 - PLAYBACK ON STAND.
For use with loudspeaker on stand, specifically designed for musical playback
(MP3 players, CDs, etc.).
7) POWER SWITCH "POWER"
This switch can be used to switch the speaker on and off.
8) FUSE CARRIER "FUSE"
Mains fuse housing. Replace only with identical value!
9) POWER CABLE SOCKET "MAINS"
8