Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GSR Professional 180-LI Notice Originale

Pre-selecting the torque
The torque presetting ring (3) can be used to pre-select the
required torque in 20 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical Gear Selection
You can press the gear selector switch (5) with the
u
power tool off or on. You should not do this at full load
or maximum torque, however.
Gear I:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Gear II:
High speed range; for working with a small drilling diameter.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the battery tem-
perature is not kept within the permitted range, the power
tool switches off and the LED on the power tool flashes. Al-
low the power tool to cool down before you carry on work-
ing.
Protection against deep discharge
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Emergency switch-off (KickBack Control)
The emergency switch-off function (Kick-
Back Control) gives the user greater control
over the power tool and offers them better
protection than power tools that do not
have KickBack Control. The power tool will switch off if it
suddenly and unforeseeably rotates around the drilling
axis.
Rapid shut-off is indicated by the LED on the power tool
flashing.
To switch the tool back on, release the on/off switch and
then press it again.
If the KickBack Control function is defective, it will no
u
longer be possible to switch the power tool on. Have
the power tool serviced by a qualified repair person
using only original replacement parts.

Working Advice

Always slide the gear selector switch or turn the mode
u
selector switch as far as it will go. Otherwise, the power
tool may become damaged.
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
An auxiliary tool can be used to remove the screwdriver bit
or universal bit holder.
Working in especially dusty environments can lead to
u
failure of the power tool. If the power tool suddenly
fails, remove the carbon brushes and check them (see
section "Replacing the carbon brushes").
Bosch Power Tools

Maintenance and Service

Maintenance and cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Replacing the carbon brushes (see figure C)
Check the length of the carbon brushes around every 2–3
months and replace both carbon brushes if required.
Never replace only a single carbon brush.
Note: Only use carbon brushes supplied by Bosch and inten-
ded specifically for your product.
– Unscrew the caps (6) using a suitable screwdriver.
– Replace the spring-loaded carbon brushes (14) and
screw on the caps again.
If the battery is no longer working, please contact an author-
ised after-sales service centre for Bosch power tools.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
English | 19
1 609 92A 5PY | (27.03.2020)