Battery Charge Indicator; Dust/Chip Extraction; Starting Operation - Bosch GSR Professional 180-LI Notice Originale

18 | English

Battery Charge Indicator

The green LEDs on the battery charge indicator (16) indic-
ate the state of charge of the battery (7). For safety reasons,
it is only possible to check the state of charge when the
power tool has been stopped.
Press the battery charge indicator button (15) to show the
state of charge. This is also possible when the battery is re-
moved.
If no LED lights up after pressing the battery charge indicator
button (15), the battery is defective and must be replaced.
Battery Model GBA 18V... (see figure D1)
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
3× flashing green light
Battery Model ProCORE18V... (see figure D2)
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the Tool (see figure A)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
1 609 92A 5PY | (27.03.2020)
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation

Starting Operation

Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (10) to the middle posi-
tion to avoid unintentionally switching it on. Insert the
charged battery (7) into the handle until you feel it engage
Capacity
and it is flush with the handle.
60−100 %
Setting the rotational direction (see figure B)
30−60 %
The rotational direction switch (10) is used to change the ro-
5−30 %
tational direction of the power tool. However, this is not pos-
0−5 %
sible while the on/off switch (11) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (10) through to the left stop.
Capacity
Left Rotation: To loosen and unscrew screws and nuts,
80−100 %
press the rotational direction switch (10) through to the
60−80 %
right stop.
40−60 %
Setting the operating mode
20−40 %
5−20 %
0−5 %
quired torque.
GSB:
Set the mode selector switch (4) to the "drilling" symbol.
GSB:
Set the mode selector switch (4) to the "screwdriving" sym-
bol.
Switching on/off
To start the power tool, press and hold the on/off switch
(11).
The LED (9) lights up when the on/off switch (11) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (11).
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (11) to varying extents.
A light pressure on the on/off switch (11) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Drilling
GSR:
Set the torque presetting ring (3) to the re-
Screwdriving
GSR:
Set the torque presetting ring (3) to the
"screwdriving" symbol.
Impact drilling (GSB)
Set the mode selector switch (4) to the "im-
pact drilling" symbol.
Bosch Power Tools