Water Supply Requirements; Water Pressure; Tipping Radius - Dacor Discovery DYF42BIWS Instructions D'installation

Water Supply Requirements

All installations must meet local plumbing code requirements.
ƒ
The water shutoff should be located in the base cabinet on
ƒ
either side of the refrigerator or some other easily accessible
area. The right-hand side is recommended. The access hole
through the cabinet must be within ¹⁄
NOTE: If the water shut off valve is in the back wall behind the
refrigerator, it must be at an angle so that the water line is not
kinked when the refrigerator is pushed into its final position.
(2.5 cm x 2.5 cm)
Possible water
line locations
6"
(15.2 cm)
If the water shutoff valve is not in the cabinets, the plumbing
ƒ
for the water line can come through the floor. A ¹⁄
hole for plumbing should be drilled at least 6" (15.2 cm) from
the right or left hand side cabinet or panel. On the floor, the
hole should be no more than 1" (2.5 cm) away from the back
wall. See Connect Water Supply.
If additional tubing is needed, use copper tubing and check
ƒ
for leaks. Install the water supply line only in areas where the
household temperatures will remain above freezing.
Do not use a piercing-type or ³⁄
ƒ
reduces water flow and clogs more easily.
NOTE: Your refrigerator dealer has a kit available with a ¹⁄
mm) saddle-type shutoff valve. Make sure a saddle-type valve
complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of
a reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and 827
kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
4
Installation Requirements
" (1.3 cm) of the rear wall.
2
1" x 1"
1"
(2.5 cm) 6"
(15.2 cm)
" (1.3 cm)
2
" (4.8 mm) saddle valve which
16
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
Check to see whether the sediment filter in the reverse
ƒ
osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill
ƒ
after heavy usage.
If your refrigerator has a water filter cartridge, it may further
ƒ
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator
upright when it is moved into place.
The dolly wheel height must be added to the tipping radius
ƒ
when a dolly is used.
If needed, the tipping radius can be reduced. See Reduce
ƒ
Tipping Radius.
Side Tipping Radius
The side tipping radius varies depending upon the width of the
model. Use the chart provided to determine the side tipping
radius.
" (6.4
4
NOTE: Tip on side only.
DYF42BIWS
DYF48BIWS
A A
Model Tipping Radius A
93" (236.2 cm)
96" (243.8 cm)