Proper Use; Technical Data; Important - EINHELL TE-TS 36/210 Li-Solo Instructions D'origine

•
10/13 mm ring wrench
•
10/21 mm ring wrench
•
Original operating instructions
•
Safety information

3. Proper use

The cordless bench-type circular saw is designed
for the slitting and cross-cutting (only with the
cross stop) of all types of timber commensurate
with the machine's size. The equipment is not to
be used for cutting any type of round wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades (saw blades made of HM or CV)
It is prohibited to use any type of HSS saw blade
and cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
Anl_TE_TS 36_210_Li_Solo_SPK9.indb 28
GB
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

Motor power supply ................................36 V d.c.
Idle speed n : ......................................3800 min
0
Carbide saw blade: ...........ø 210 x ø 30 x 1.8 mm
Number of teeth: ............................................ 40
Cutting height max. ........................... 70 mm / 90°
........................................................ 45 mm / 45°
Height adjustment .................... infi nite 0 - 70 mm
Tilting saw blade .......................... infi nite 0° - 45°
Cross stop angle ..................... infi nite -60° - +60°
Extractor connection .............................Ø 36 mm
Weight: .......................................... approx. 13 kg
Thickness of the splitter .......................... 1.6 mm
This machine is equipped with a special precision
cut saw blade (cutting width 1.8 mm). If you use a
diff erent saw blade with a larger cutting width, this
could result in loss of performance.

Important!

The equipment is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries of the Power-X-
Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with Power-
X chargers.
Suitable rechargeable batteries and chargers
from the Power X-Change range are for example:
•
Rechargeable battery: Power-X-Change 1.5
•
Rechargeable battery: Power-X-Change 5.2
•
Charger: Power-X-Charger 3A
•
Charger: Power-X-Charger
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
- 28 -
-1
29.10.2020 08:42:57