Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
7 Press the [ON/OFF] button, and register the set indoor unit address
and LOSSNAY address.
- Registration end display
The indoor unit address and "IC" and LOSSNAY address and "LC"
are alternately displayed.
- Registration error display
If the address is not registered correctly, the indoor unit address and [
] and the registered LOSSNAY or OA processing unit address and
[
] are alternately displayed.
Cannot be registered because the registered indoor unit or LOSSNAY
or OA processing unit does not exist.
Cannot be registered because another LOSSNAY or OA processing
unit was registered at the registered indoor unit.
< 2. Confirmation procedure >
8 Set the address of the indoor unit connected by the remote con-
troller whose LOSSNAY or OA processing unit you want to confirm
using the [TEMP. (
) and (
)] buttons. (01 to 50)
9 Press the [ON/OFF] button and [
button simultaneously for 2 seconds, and check the Lossnay ad-
dress registered at the set indoor unit address.
- Confirmation end display (When LOSSNAY is connected.)
The indoor unit address and "IC" and registered LOSSNAY ad-
dress and "LC" are alternately displayed.
7
Function Selection
Set the functions of each indoor unit from the remote controller, as required. The functions of each indoor unit can be selected only from the remote controller.
Set the functions by selecting the necessary items from Table 1.
Table 1. Function selection contents (For a detailed description of the factory settings and mode of each indoor unit, refer to the indoor unit installation manual.)
Function
Power failure automatic
Not available
recovery
Available (Approximate 4 minutes wait-period after power is restored.)
Indoor unit operating average
Indoor temperature
Set by indoor unit's remote controller
detecting
Remote controller's internal sensor
Not Supported
OA processing unit
Supported (indoor unit is not equipped with outdoor-air intake)
connectivity
Supported (indoor unit is equipped with outdoor-air intake)
240 V
Power voltage
220 V, 230 V
Energy saving cycle automatically enabled
AUTO mode
Energy saving cycle automatically disabled
100 Hr
Filter sign
2500 Hr
No filter sign indicator
Quiet
Fan speed
Standard
High ceiling
4 directions
No. of air outlets
3 directions
2 directions
Installed options (high-
Not supported
performance filter)
Supported
No vanes
Up/down vane setting
Equipped with vanes (No. 1 set)
Equipped with vanes (No. 2 set)
Energy saving air flow
Disabled
(Heating mode)
Enabled
Humidifier
Not supported
(Direct Add-on type)
Supported
NOTE: When the indoor unit functions were changed using the function selection after installation is complete, always indicate the set contents by
entering
or other mark in the appropriate check field of Table 1.
[Function selection flow]
First grasp the function selection flow. The following describes setting of "Room temperature detection position" of Table 1 as an example.
(For the actual setting procedure, see [Setting procedure] 1 to ?.)
LC: LOSSNAY
FU: OA Process-
ing unit
(Fan Speed Adjustment)]
LC: LOSSNAY
FU: OA Process-
ing unit
Please set the following functions connected with Mr.SLIM if it is neccessary.
(Cannot be performed with CITY MULTI Control system.)
Settings
Standard
High ceiling 1
PL(H)(A)-P·AA type
High ceiling 2
- Confirmation end display (When
LOSSNAY or OA processing unit
is not connected.)
< 3. Deletion procedure >
Use this procedure when you want to delete registration of indoor units
connected by the remote controller and LOSSNAY or OA processing unit.
; Confirm (see 2. Confirmation procedure) the LOSSNAY or OA pro-
cessing unit you want to delete and display the indoor units and
LOSSNAY or OA processing unit confirmation results.
A Press the [TEMP. (
) and (
onds, and delete registration of the LOSSNAY or OA processing unit
address registered at the set indoor unit.
- Deletion end display
Indoor unit address and "– –" and registered LOSSNAY or OA pro-
cessing unit address and "– –" are alternately displayed.
- Deletion error display
When deletion was not performed properly.
Mode No.
Setting No.
Check
01
1
01
2
02
1
02
2
02
3
03
1
03
2
03
3
04
1
04
2
05
1
05
2
07
1
07
2
07
3
08
1
08
2
08
3
09
1
09
2
09
3
10
1
10
2
11
1
11
2
11
3
12
1
12
2
13
1
13
2
- Registered indoor unit ad-
dress does not exist.
LC: LOSSNAY
FU: OA Process-
ing unit
)] button simultaneously for 2 sec-
Object unit address No.
Unit address No. 00
These items are set for all in-
door units.
Unit address No. 01 to 04 or
AL
These items are set for each
indoor unit.
5
Publicité
Table des Matières
