Precautions For Cassette Loading In The "Service Position; Cassette Loading And Ejection Methods In The; Service Position"(See Fig. 1-4-3); Mechanism Service Mode - JVC HR-S6700MS Mode D'emploi

www.freeservicemanuals.info
Note:
• When carrying out diagnosis and repair of the Main
board assembly in the service position, be sure to
ground both the Main board and the Mechanism as-
semblies.
If they are improperly grounded, there may be noise
on the playback picture or the FDP counter display may
move even when the mechanism is kept in an inopera-
tive status.
1.4.2 Precautions for cassette loading in the "SERVICE
POSITION"
The REC safety board assembly detects cassette loading as
well as cassette tabs. Therefore, after the assembly has been
removed in the "SERVICE POSITION", it is required to set
the switch manually on the REC safety board assembly when
a cassette is loaded.

1.4.3 Cassette loading and ejection methods in the

"SERVICE POSITION"(See Fig. 1-4-3).

(1) Insert a cassette halfway in the Cassette holder assembly.
(2) Set the switch on the REC safety board assembly to ON
(by pressing the switch).
(3) As soon as the cassette starts to be loaded, set the switch
on the REC safety board assembly to OFF (by releasing
the switch).
(4) Now the desired operation (recording, playback, fast for-
ward, rewind, etc.) is possible in this status (the status
shown in Fig.1-4-3).
Notes:
• When performing diagnostics of the tape playback or
the recording condition in the "SERVICE POSITION",
enter the desired mode before turning the set upside
down, and do not change the mode when performing
diagnostics while the set is placed upside down. If you
want to switch the mode, turn the set to the normal po-
sition (the status shown in Fig.1-4-3).
P/S Converter board
assembly
S-Sub board assembly
DEMOD board assembly
CN513
CN3502
CN6102
CN3501
CN901
CN902
CN7192
Jack board assembly
CN7191
SW/Display board assembly
Fig. 1-5-1
Published in Heiloo Holland
• In the "SERVICE POSITION", the cassette tabs cannot
be detected and recording becomes possible even with
a cassette with broken tabs such as the alignment tape.
Be very careful not to erase important tapes.
(5) The switch on the REC safety board assembly does not
have to be operated when ejecting a tape. But be sure
to turn the set to the normal position before ejecting the
tape.

1.5 MECHANISM SERVICE MODE

This model has a unique function to enter the mechanism
into every operation mode without loading of any cassette
tape. This function is called the "MECHANISM SERVICE
MODE".

1.5.1 How to set the "MECHANISM SERVICE MODE"

(1) Disconnect VCR from AC.
(2) Connect TPGND and TP7001 (TEST) on the SW/Display
board assembly with a jump wire.
(3) Connect VCR to AC.
(4) Press the POWER button.
Åı
(5) With lock levers on the left and right of the Cassette
holder assembly pulled toward the front, slide the holder
in the same direction as the cassette insertion direction.
(For the positions of lock levers
cedures for Lowering the Cassette holder assembly" on
pages 1-2 of 1.3 DISASSEMBLY/ASSEMBLY METHOD.)
(6) The cassette holder lowers and, when the loading has
completed, the mechanism enters the desired mode.
2D Digital [HR-S6700MS] or
3D Digital/2M [HR-S7700MS] board assembly
Terminal board assembly
TP111
TP4001
D.FF
VR1401
CTL.P
D/A LEVEL ADJ
Main board assembly
TP2253
TP106
[HR-S7700MS]
A.FM
PB.FM
Audio erase
CP4001
board assembly
CP5302
CP5301
CN3012 [HR-S7700MS]
CN3011
CN7002
[HR-S6700MS]
REC safety board
assembly
TP7001 (TEST) TPGND
8/6/2016
Åı
, refer to the "Pro-
To Jog [HR-S7700MS]
CN7001
To Shuttle play [HR-S6700MS]
1-5