Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
E N G L I S H
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
2
size is 1.5 mm
. When using a cable reel, always
unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Fitting sanding discs (fig. B)
Your D
WALT palm grip sander uses 5" (126 mm)
E
Velcro sanding discs with an 8 hole dust extraction
pattern.
• Place the sander on a table, sanding pad (7) up.
• Place the sanding disc directly on top of the
sanding pad.
en - 4
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Hold the sanding pad (7) with one hand and align
the dust extraction holes (9).
.
Electronic speed control dial (fig. C)
Your D
WALT palm grip sander is equipped with an
E
electronic speed control dial (2) with 5 positions.
Generally, harder materials require a higher setting.
The correct setting, however, is a matter of
experience.
Dust extraction
Since woodworking with a sander produces dust,
always install the dust collector or connect a
vacuum extractor designed in compliance with the
applicable Directives regarding dust emission.
Proper dust extraction will only be achieved with
perforated abrasive.
60
6
10
15
20
Dust collector (fig. A & D)
25
Your D
WALT palm grip sander is equipped with a
E
-
dust collector (3).
-
-
• Attach the dust collector (3) with the vacuum
6
6
extractor adaptor (4) to the spout (5).
6
6
• For efficient dust extraction empty the dust
15
collector when it is about one third full.
15
• To empty the dust collector, pull it off together
20
with the adaptor (4) and separate both parts.
-
• Gently empty the dust collector (3) and shake out
the adaptor (4).
• If necessary, use a vacuum extractor to clean the
dust collector, applying suction to the interior
surface.
Vacuum extractor (fig. D)
• Remove the dust collector (3) by rotating it and
pulling it firmly off the vacuum extractor adaptor (4).
• Attach the vacuum extractor hose to the vacuum
extractor adaptor (4).
Do not use a dust collector or vacuum
extractor without proper spark protection
when sanding metal.
Do not sand magnesium!
15
Publicité
Chapitres
Table des Matières
