EdilKamin LOGO Installation, Usage Et Maintenance page 29

Should the pellet hopper empt completel the feed screw
must be lled. o do so, keep the
taneousl for a few seconds (on the remote control or s noptic
panel). Once released, REF LL will appear on the displa .
his must be carried out before ignition if the stove has stopped
due to the pellets having nished.
t is quite normal for some pellet residue to remain inside the
hopper, this is what the feed screw is unable to pick up.
Once a month, full vacuum the hopper to prevent dust resi-
due from accumulating.
With the stove on standb , press the
(on the s noptic panel or remote control). his will startup
the ignition process, Start will appear on the displa and a
countdown will commence in seconds (
preset time for the ignition process its duration will be automa-
ticall shortened if the control board detects that certain tests
have been carried out positivel . he ame appears after about
minutes.
t a temperature lower than
resistance to become red hot - or if the resistance is temporaril
not working, ou can use a relighter to ignite the stove.
nsert a well-lit relighter into the combustion chamber, close
the door and press on the s noptic panel or remote control.
the user sets the desired operating power (from
a minimum of to a ma imum of )
the user sets the temperature desired in the
room. he stove reads this and ad usts the power to reach
the set temperature. Once this is reached, it sets itself to
power .
With the stove in operation mode or on standb , press and
release the E button on the s noptic panel remote
control and ower will appear on the displa (showing
the power at which the stove is working). Rotate the left
knob or press the ke on the remote control to increase
the operating power (from ower to ower ).
Setting the fan via the S noptic anel
With the stove in operation mode or on standb , rotate the
right knob to ad ust the ventilation setting (from to
all powers).
ress the E button twice to switch from manual to
automatic mode and ad ust the temperature desired for the
room (use the left knob on the panel or the
on the remote control to set the temperature between
and 9 ...., and the stove will regulate the operating power
required to reach it.
f the set temperature is lower than the room temperature,
the stove works at ower .
INSTRUCTIONS FOR USE
and ke s pressed simul-
button for seconds
). here is no
too low for the electrical
in
and ke s
- 29
With the stove in operation mode press the
seconds (on the s noptic panel or remote control). he
shutdown procedure will begin and the countdown is
displa ed. his varies according to the power at which it
is running when the shutdown phase begins.
he shutdown phase (which will e tinguish the ame
without leaving an unburnt material in the combustion
chamber and cool the stove), consists of
ellet loading ceases.
entilation is activated at the level at which the stove
was operating.
Smoke e pulsion motor enabled.
ress the E button for seconds and use the
ke s to follow the instructions given on the displa to
access the lock menu. his allows ou to set the time on the
electronic control board.
hen press E and the following data appears in
sequence this can be ad usted
da , month, ear, hour, minutes, da of the week.
When Save appears on the displa
the settings have been entered correctl before con rming.
ress E to save the information ( Save OK then
appears on the displa ).
ress the E button on the remote control for
seconds to access the time setting function and press the
ke to access the weekl timer function
OFF will appear on the displa .
ma imum of three timer programs can be set for each
da of the week.
s ou con rm via the E
options will appear
- o rog. (no program is set).
- ail program (a single program is set for ever da )
- Weekl program (a program is set for each da of the
week).
ove from one to the other using the
se the E button to con rm the
option and access the selection of the number of programs
(ignition shutdown) to be set per da . se the
option to set the identical program s for ever da
of the week.
he following will be displa ed if the
- o rograms.
- st dail program (one ignition and one shutdown per
da ), nd dail program (same as before), rd dail program
(same as before).
se the E button to show them in reverse order.
f the st program is selected, the ignition time is shown.
he displa shows gnition our
ke s to change the hour and press
he displa shows gnition
ke s to change the minutes and press
-
ke for
and
ou can check that
rogram O
button, one of the following
and ke s.
ail program
ail program
ke is pressed
. ; use the
E to con rm.
inutes . ; use the
E to con rm.