Geräterückwand; Netzspannung; Rear Panel; Mains Voltage - Ismatec ISM 915 Mode D'emploi

Masquer les pouces Voir aussi pour ISM 915:
Table des Matières

Publicité

1
4
2
5
3
Hinweis
Für die Benutzung der Analog- oder
RS232-Schnittstelle unter IP 65 Bedingungen
verweisen wir auf Seite 58.
Please note
For using the analog or RS232- interface under
IP 65 conditions please refer to Page 58.
Remarque
Pour l'utilisation de l'interface analogique ou
RS232 sous des conditions IP 65: voir Page 58.
MCP PROCESS, 14-014, REV. C
Geräterückwand
1. Netzschalter (ein/aus)
2. Netzkabel
3. RS232 IN (Eingang, weiblich)
4. RS232 OUT (Ausgang, männlich)
5. Analog-Schnittstelle
X
X
Eingänge für:
– Drehzahlsteuerung
0 – 5 V oder 0 – 10 V, bzw.
0 – 20 mA oder 4 – 20 mA
– Drehrichtung
– Start/Stopp
– Fußschalter
– 2 digitale Eingänge (TTL-Pegel)
X
X
Ausgänge für:
– Drehzahl 0 – 10 V
DC
oder 0 – 7.2 kHz
– 2 Universal-Ausgänge
!

Netzspannung

100 - 240 V
AC
50/60 Hz
ohne Umschaltung
Leistungsaufnahme
Max. 100 W
Absicherung auf Steuerprint*
F1.6A/250V
T4A/250V
Absicherung auf Netzteilprint*
T3.15A/250V
* Siehe auch Seite 59
!
Steckdose/Netzkabel
Die Steckdose muss geerdet sein.
(Schutzleiterkontakt)

Rear panel

1. Mains switch (on/off)
2. Power cord
3. RS232 IN (female)
4. RS232 OUT (male)
5. Analog interface
X
X
input for:
– speed control
0 – 5 V or 0 – 10 V, and
0 – 20 mA or 4 – 20mA
– rotation direction
– Run/Stop
– Footswitch
– 2 digital inputs (TTL-level)
X
X
Output for:
– speed 0 – 10 V
DC
or 0 – 7.2 kHz
– 2 universal outputs
!

Mains voltage

100 - 240 V
AC
50/60 Hz
no adjustments necessary
Power consumption
Max. 100 W
Fuse rating on control board*
F1.6A/250V
T4A/250V
Fuse rating on power supply print*
T3.15A/250V
* See also Page 59
!
Socket/Power cord
The socket must be earthed.
(protective conductor contact)
Panneau arrière
1. Interrupteur principal
2. Prise d'alimentation
3. RS232 IN (entrée femelle)
4. RS232 OUT (sortie mâle)
5. Interface analogique
X
X
Entrée:
– commande de vitesse
0 – 5 V ou 0 – 10 V, resp.
0 – 20 mA ou 4 – 20mA
– sens de rotation
– marche/arrêt
– Pédale de commande
– 2 entrées numériques (TTL-level)
X
X
Sortie:
– vitesse 0 – 10 V
CC
ou 0 – 7.2 kHz
– 2 sorties universelles
!

Tension d'alimentation

100 - 240 V
CA
50/60 Hz
sans commutation
Consommation de courant
Max. 100 W
Type de fusibles sur le panneau
de commande*
F1.6A/250V
T4A/250V
Type de fusibles sur le panneau
réseau*
T3.15A/250V
* Voir aussi Pages 59
!
Prise/câble d'alimentation
La prise doit être raccordée à la terre
(contact conducteur de protection).
8 of 63

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mcp process ism 915

Table des Matières