Nice ARIA200 Manuel D'installation Et D'utilisation page 31

CONTENTS
QUICK GUIDE (images only)
1 GENERAL WARNINGS: SAFETY - INSTALLATION - USE
2 PRODUCT DESCRIPTION AND INTENDED USE
3 INSTALLATION
3.1 VERIFYING THE SUITABILITY OF THE GATE AND ENVIRONMENT
3.2 VERIFYING THE PRODUCT'S APPLICATION LIMITS
3.3 PRODUCT TECHNICAL SPECIFICATIONS
3.4 PRE-INSTALLATION WORKS
3.5 INSTALLING THE ARIA GEARMOTORS (models 400C/600C) and CLB CONTROL UNIT (models 202/203)
3.5.1 INSTALLING THE ARIA GEARMOTORS 200M/400M
3.5.2 INSTALLING THE CLB202/203 CONTROL UNIT
3.6 INSTALLING THE PHOTOCELLS model PH200
3.7 INSTALLING THE FLASHING LIGHT model FL200
4 ELECTRICAL CONNECTIONS
4.1 ELECTRICAL CONNECTION TO THE CONTROL PANEL
4.2 POWER SUPPLY CONNECTION
5 PROGRAMMING
5.1 CONTROL UNIT KEYS
5.2 INITIAL CHECKS
5.3 MEMORISATION OF CONNECTED DEVICES
5.4 MEMORISATION OF GATE LEAF OPENING AND CLOSING ANGLES
5.5 MEMORISATION OF THE 1
5.6 BASIC ADJUSTMENTS
5.6.1 Choosing the gate leaf manoeuvre speed
5.6.2 Choosing the operating cycle of the gate leaf manoeuvre
6 TESTING AND COMMISSIONING
6.1 TESTING
6.2 COMMISSIONING
7 MAINTENANCE
8 PRODUCT DISPOSAL
9 FURTHER INFORMATION
9.1 ADVANCED ADJUSTMENTS
9.1.1 Adjusting the parameters using the transmitter
9.1.1.1 Parameter adjustment procedure: Pause time - Pedestrian opening - Motor force - Step-by-Step function
9.1.1.2 Parameter adjustment procedure: SbS input configuration - Flash output configuration - Discharging of Motor 1
and 2 upon closing - Discharging of Motor 1 and 2 upon opening
9.1.2 Verifying the values set for each parameter (using the transmitter)
9.1.2.1 Parameter verification procedure: Pause time - Pedestrian opening - Motor force - Step-by-Step Function
9.1.2.2 Parameter verification procedure: Discharging of Motor 1 upon closing - Discharging of Motor 1 upon opening -
Discharging of Motor 2 upon closing - Discharging of Motor 2 upon opening
9.2 ADDING OR REMOVING DEVICES
9.2.1 Memorising additional devices
9.3 MEMORISING ADDITIONAL TRANSMITTERS
9.3.1 Mode 1 memorisation procedure
9.3.2 Mode 2 memorisation procedure
9.3.3 Memorisation procedure near the control unit with two transmitters
9.4 DELETING THE MEMORY OF THE INDIVIDUAL TRANSMITTER FROM THE CONTROL UNIT'S MEMORY
9.5 COMPLETE DELETION OF THE RADIO MEMORY
9.6 INSTALLING THE BACK-UP BATTERY
9.7 INSTALLING THE SOLAR POWER SYSTEM KIT model SOLEKIT
9.8 DIAGNOSTICS AND DEVICE SIGNALS
9.8.1 Photocell signals
9.8.2 Flashing light signals
9.8.3 Control unit signals
9.9 SPECIFICATIONS
9.9.1 ECSbus system
9.9.2 Stop input
9.9.3 Product durability
10 TROUBLESHOOTING
EC Declaration of Conformity
11 USER GUIDE (to be delivered to the end user) (detachable insert)
ANNEX I (detachable insert)
ST TRANSMITTER
II-X
4
4
4
4
4
4
5
6
6
6
6
6
7
7
7
7
7
7
7
8
8
9
9
9
10
10
10
10
10
11
11
11
11
12
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
14
14
16
16
16
16
17
18
A
B
English - 1