Accessories; Environmental Protection; Technical Data - Metabo KFM 9-3 RF Notice Originale

en ENGLISH
overloaded. Reduce the load before continuing to
work.
- Metabo S-automatic safety shut-down: The
machine has SHUT DOWN by itself. If the slew
rate of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch off the machine
using the slide switch (4). Switch it on again and
continue to work as normal. Try to prevent the
machine from seizing. See chapter 4.1.
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
11.2 Cordless machines:
- The electronic signal display (8) lights up and
the load speed decreases. The temperature is
too high! Run the machine in idling until the
electronics signal indicator switches off.
- The electronic signal display (8) flashes and
the machine does not start. The restart
protection is active. The machine will not start if
the battery pack is inserted while the machine is
on. Switch the machine off and on again.

12. Accessories

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: Secure the machine well. Loss of control
can cause personal injury.
A Indexable inserts
HM-indexable insert 45° .................. 6.23560
HM-indexable insert R 2 .................. 6.23561
HM-indexable insert R 3 .................. 6.23562
B Chargers: ASC Ultra, ASC 15, ASC 30 and others
C Battery packs with different capacities. Use
battery packs only with voltage suitable for your
power tool.
For a complete range of accessories, see
www.metabo.com or the catalogue.
13. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

14. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
16
Only for EU countries: Never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Special notes regarding cordless machines:
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).

15. Technical Data

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
n = no-load speed (maximum speed)
P = Rated input power
1
P = Power output
2
m = Weight with smallest battery pack/weight
without cord
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
AC Power
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user e.g. organisational
measures based on the adjusted estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a =Vibration emission value
h, SG
K =Uncertainty (vibration)
h,SG
Typical A-effective perceived sound levels:
L = sound-pressure level
pA
L = Acoustic power level
WA
K , K =Uncertainty
pA WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Problems, faults:
In individual cases, the speed may fluctuate
temporarily if the machine is exposed to extreme
external electromagnetic disturbances or the