Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
CHARGER
Model
EB14B
Charging time
(at 20°C)
BCH1415
Charging voltage
Weight
NOTE: The charging time may vary according to the ambient temperature and power source voltage.
STANDARD ACCESSORIES
1. Charger (UC18YG or UC18YGH) .............................. 1
2. Battery (EB14B or BCH1415) .................................... 2
3. Plastic case ................................................................ 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES
(Sold separately)
1. Battery (EB14B, BCH1415)
Optional accessories are subject to change without notice.
APPLICATION
Driving and removing of small screws, small bolts,
etc.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery. (See Fig. 1 and 2)
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities. (See
Fig. 2)
CHARGING
〈UC18YG〉
Before using the power tool, charge the battery as follows.
1. Connect the charger power cord to the receptacle
Connecting the power cord will turn on the charger.
2. Insert the battery into the charger
Insert the battery firmly while observing its direction,
until it contacts the bottom of the charger (the pilot
lamp lights up) (See Fig. 3).
CAUTION
If the pilot lamp does not light up, pull out the
power cord from the receptacle and check the
battery mounting condition.
Regarding the temperatures of the rechargeable
battery
The temperatures for rechargeable batteries are as
shown in Table 1.
UC18YG
Approx. 50 min.
–––––
7.2 – 18 V
0.3 kg
Table 1 Recharging ranges of batteries
Rechargeable
batteries
EB14B
BCH1415
The pilot lamp goes off to indicate that the battery is
fully charged.
The battery charging time becomes longer when a
temperature is low or the voltage of the power source
is too low.
When the pilot lamp does not go off even if more
than 120 minutes have elapsed after starting of the
charging, stop the charging and contact your HITACHI
AUTHORIZED SERVICE CENTER.
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may
not light up. At that time, cool the battery first,
then start charging.
3. Disconnect the charger's power cord from the
receptacle
4. Hold the charger firmly and pull out the battery
NOTE
After charging, pull out batteries from the charger
first, and then keep the batteries properly.
〈UC18YGH〉
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a
receptacle, the pilot lamp will blink in red
(At 1-second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger till it contacts
the bottom of the charger and checking the polarities
as shown in Fig. 3.
CAUTION
If the batteries are inserted in the reverse direction,
not only recharging will become impossible, but
it may also cause problems in the charger such as
a deformed recharging terminal.
3. Charging
When inserting a battery in the charger, the pilot
lamp will light up continuously in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red (At 1-second intervals).
(See Table 2)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 2, according to the condition of the charger or
the rechargeable battery.
English
UC18YGH
Approx. 50 min.
Approx. 35 min.
7.2 – 18 V
0.35 kg
Temperatures at
which the
battery can be recharged
UC18YG
UC18YGH
0°C – 45°C
-5°C – 55°C
–––––
-5°C – 50°C
6
Publicité
Table des Matières
