Description; Specifications - RIDGID RE 6 Mode D'emploi

RE 6/RE 60/RE 600 Electrical Tools
Green
Red
Yellow
Figure 6 – Tool Status Lights

Specifications

*
With 2 Ah Battery
Figure 7 – Specification Chart
Piston Force ...............60 kN (6-ton) (13,500 lbs.)
QCS Coupling Type ...RE 6
RE 60
RE 600 Series – N/A
Duty Cycle..................
Motor
Voltage ...................18V DC
Amperage ...............18 Amp
Power .....................324 Watts
Battery........................18V Li-Ion, Rechargeable Batter y
(see Optional Equipment)
Ingress Protection .......IP32
Allowable Humidity......0-80%
6
Solid Light Blinking Light
Icon
Green
Red
Yellow
Model

Description

RE 6 6T Tool For Use
w/Interchangeable Heads
RE 60 60 kN Tool For Use
w/Interchangeable Heads
RE 600 RDH Latching Round
Die Head
RE 600 SC Scissor Cut
Head*
RE 600 4PI 4 PIN Indenter
Head
*
1
Includes dies
6T QCS
60 kN QCS
3 Cycles per minute
Meaning
Tool ON, ready to use.
Green Battery low. Tool will not operate. Recharge
battery/Insert fully charged battery.
Tool out of Specification temperature range. Bring tool
and battery to correct operating temperature range.
Indicates service interval approaching. Starts 2,000
Yellow
cycles prior to service interval (see Figure 7). Tool is
usable, but tool will lock after service interval.
Tool is locked. Tool has completed service interval
(see Figure 7) and requires service.
Tool has malfunctioned. Have serviced.
Weight
*
L x H x W (mm)
g lbs
L x H x W (inch)
3000 6.6 318 x 154 x 73
12.5 x 6.1 x 2.9
3000 6.6 318 x 154 x 73
12.5 x 6.1 x 2.9
4300* 1 9.5 395 x 165 x 73
15.6 x 6.5 x 2.9
4800 10.5 473 x 174 x 73
18.6 x 6.9 x 2.9
2
5300 11.7 474 x 192 x 73
18.7 x 7.6 x 2.9
*
2
Versions for Cu/Al wire and ACSR available - See blade markings.
Operating Temperature
Range ...........................15° F to 122° F (-10° C to 50° C)
Storage Temperature
Range ...........................32° F to 113° F (0° C to 45° C)
Sound Pressure (L
Sound Power (L )*.......76 dB(A), K=3
WA
Vibration .......................<2.5 m/s
*
* Sound and Vibration measurements are measured in accordance with a stan-
dardized test per Standard EN 62481-1.
- Vibration levels may be used for comparison with other tools and for pre-
liminary assessment of exposure.
- Sound and vibration emissions may vary due to your location and specific use
of these tools.
- Daily exposure levels for sound and vibration need to be evaluated for each
application and appropriate safety measures taken when needed. Evaluation
of exposure levels should consider the time a tool is switched off and not in
use. This may significantly reduce the exposure level over the total working
period.
Go to RIDGID.com/CrimpDies for the RIDGID Crimp
Dimensions Piston Travel
mm inch
32 1.3
32 1.3
17 0.7
24 0.9
32 1.3
)* ...65 dB(A), K=3
PA
2 , K=1.5
999-999-463.08_REV. H
Service
Interval
Cycles
32,000
32,000
32,000
32,000
32,000