Milwaukee MX FUEL MXF368 Manuel De L'utilisateur page 5

6. To remove, rotate the clamp arm and remove the
chisel.
NOTE: Use caution when handling hot chisels.
Installing Collared Chisels
1. Clean and grease the shank.
2. Rotate the clamp arm to the open position.
Collar retention
3. Insert the chisel into the nose of the machine.
4. Rotate the clamp arm to secure the collar retention
around the shank, as shown.
5. Pull on the chisel to verify that it is held in place.
6. To remove, rotate the clamp arm and remove the
chisel.
NOTE: Use caution when handling hot chisels.
Transporting
(Accessory Breaker Cart 3600)
To reduce the risk of injury, strap
WARNING
securely before transporting. Re-
move chisels from machine before placing on
cart. Insert cart post into chisel receiver. Do not
lift/hoist loaded cart.
Use the accessory Breaker Cart to transport the
Breaker.
1. Remove the chisel from the machine before
placing the breaker on the cart.
2. Slide the chisel receiver over the cart post.
3. Secure with belt. WARNING! Always secure with
belt before transporting.
1. Cart
2. Strap
3. Chisel
storage
4. Charger
hook/strap
5. Charger
cord wrap
2
1
5
To learn more about the ONE-KEY™ functional-
ity for this machine, please reference the Quick
Start guide included with this machine or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
Solid Blue
Blinking Blue Machine is actively communicating
Blinking Red Machine is in security lockout and
WARNING
to comply with ANSI Z87.1.
When working in dusty situations, wear
appropriate respiratory protection or use an
OSHA compliant dust extraction solution.
Arming the Machine
The MX FUEL™ machines must be armed prior to
use. Even with the battery pack inserted, the trigger
and machine functions will not operate until the
machine is armed.
To arm the machine:
1. Insert the battery pack.
2. Press the Arm button. The MX FUEL™ icon will
light. The trigger will become armed in 2 seconds.
3. After 15 minutes of inactivity, the machine will enter
sleep mode. The MX FUEL™ icon will go off and
the trigger and LEDs are un-operational.
4. Press and hold the Arm button for 1 second to
reactivate the machine.
5. Press and hold the ARM button for 1 second to
unarm (turn off) the machine. The MX FUEL™
icon will go off.
Starting and Stopping
1. Insert the chisel.
2. Position the machine on the workpiece.
3. Press the arm button.
4. Grasp both handles firmly and pull the trigger. Al-
ways hold the machine securely using two handles
and maintain control.
4
5. Use only enough pressure to hold the machine in
place, engage the hammering mechanism, and
prevent the tip of the chisel from wandering. This
3 machine has been designed to achieve top per-
formance with only moderate pressure. Excessive
force reduces the vibration dampening. NOTE:
To engage the hammering mechanism, maintain
pressure on the chisel. When pressure is released,
hammering stops.
6. When chiseling or chipping, hold the machine at
an angle to the work area. For best performance,
work from a corner or close the edge of the work
and break off a small area at a time.
7. To stop the machine, release the trigger. Make
sure the machine comes to a complete stop before
laying the machine down.
8. Press the arm button to turn off the machine.
5
ONE-KEY™
ONE-KEY™ Indicator
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
with the ONE-KEY™ app.
can be unlocked by the owner via
the ONE-KEY™ app.
OPERATION
To reduce the risk of injury, always
wear proper eye protection marked