Data Transfer - Bosch GIS 1000 C Professional Notice Originale

26 | English
If the temperature is below the minimum temperature, the
temperature alarm indicator (m) flashes blue and (if this fea-
ture is switched on) a warning signal sounds.
If the temperature is above the maximum temperature, the
temperature alarm indicator (m) flashes red and (if this fea-
ture is switched on) a warning signal sounds.
To use the surface temperature alarm, open the <Main
Menu> (see "Navigating in the <Main Menu>", page 27).
– Select the <Alarm> submenu.
– Set <Alarm min/max> to <On>.
– Set the minimum temperature under <Alarm min>.
– Set the maximum temperature under <Alarm max>.
The minimum and maximum temperatures will remain saved
if you set the alarm to <Off>.

Data transfer

Saving/displaying/sending the results of a measurement
After measuring an object, the memory symbol appears on
the display to indicate that you can save the results. Press
the save/send button (9) to do this.
The results of the measurement are saved as a JPG file
(screenshot of the fixed display).
– To display saved screenshots, press the
left-hand function button (17) under the gal-
lery symbol (q). The most recently saved
photo appears on the display.
– Press the right-hand (11) and left-hand (15)
arrow buttons to scroll between the saved
screenshots.
– To send the displayed measurement results
via Bluetooth®, press the save/send
button (9). If Bluetooth® connectivity is not
yet switched on (see "Data transfer via
Bluetooth®", page 26), activate it by press-
ing the save/send button.
– To delete the displayed screenshot, press
the right-hand function button (10) under
the waste paper basket symbol.
– To confirm deletion, press the left-hand
function button (17) under the tick symbol.
– To cancel deletion, press the right-hand
function button (10) under the cross sym-
bol.
– To exit the gallery view and return to meas-
uring mode, press the left-hand function
button (17) under the "Back" symbol.
You can also delete all the files saved at the same time (see
"<Delete All Images>", page 28).
Data Transfer via USB Port
Open the cover on the micro USB port (1). Connect the mi-
cro USB port (26) of the measuring tool to your computer
via the micro USB cable (8) provided.
Now press the on/off button (12) to switch on the measuring
tool.
1 609 92A 4X3 | (03.11.2020)
Open the file browser on your computer and select the
GIS 1000 C drive. The saved files can be copied from the in-
ternal memory of the measuring tool, moved to your com-
puter or deleted.
As soon as you have finished the required operation, discon-
nect the drive from the computer following the standard pro-
cedure and then use the on/off button (12) to switch the
measuring tool off again.
Caution: Always disconnect the drive from your operating
system first (eject drive), as failure to do so may damage the
internal memory of the measuring tool.
Remove the micro USB cable during the measurement oper-
ation and close the cover (1).
Always keep the flap of the USB port closed so that dust and
splashes cannot enter the housing.
Note: Use USB to connect the measuring tool to a computer
only. The measuring tool may be damaged if connected to
other devices.
Data transfer via Bluetooth®
The measuring tool is equipped with a Bluetooth® module
which enables the data taken by your measuring tool to be
wirelessly transmitted to a mobile device. Special Bosch ap-
plications (apps) are available for this use. These can be
downloaded from the respective store of the device.
In addition to wireless data transfer, the Bosch applications
make it possible for you to use an extended range of func-
tions and facilitate post-editing and forwarding of measured
data (e.g. via e-mail). Information about system require-
ments for a Bluetooth® connection can be found on the
Bosch website at www.bosch‑professional.com/thermal.
To switch on the Bluetooth® connection on the measuring
tool, open the <Main Menu> (see "Navigating in the <Main
Menu>", page 27) and set up <Bluetooth> <On>. The
indicator (e) appears on the display. Ensure that the
Bluetooth® interface is activated on your mobile device.
The mobile device and the measuring tool will be paired with
each other when the Bosch application is started (providing
the Bluetooth® modules are activated). If multiple active
measuring tools are found, select the appropriate measuring
tool. A connection will be established automatically if only
one active measuring tool is found.
Note: When pairing the measuring tool with a mobile device
(e.g. smartphone, tablet) for the first time, you may be
prompted to enter a PIN code for the measuring tool. If you
are, enter "0000".
Bosch Power Tools