Residual Risks; Intended Use; Technical Data; Before Commissioning - Scheppach AERO2 SPADE Mode D'emploi

Residual risks

Even if you use this device in accordance with instruc-
tions, certain residual risks cannot be rules out. The
following hazards may arise in connection with the
equipment's construction and layout:
1 Lung damage if no suitable protective dust mask
is used.
2 Damage to hearing if no suitable ear protection is
used.
3 Health damage caused by hand-arm vibrations if the
equipment is used over a prolonged period or is not
properly guided and maintained.

Intended use

Depending on the tool being used, the devices de-
scribed are suitable exclusively for compacting, ram-
ming, scraping, cutting, breaking up, removing, rough-
ing, exposing, cleaning, digging or loosening different
materials. Any other use is not in compliance with the
proper intended use and as such is forbidden. Altera-
tions, use of third-party tools or tampering with or alter-
ing controls or actuators is likewise forbidden. Use in
potentially explosive areas is forbidden. Working in or
under water is not permitted.
m Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or
for equivalent purposes.

Technical Data

Overall length
Operating pressure
Air consumption, min.
Air consumption, max. (at 6.3 bar)
Stroke rate
Tool receiver
Hose internal diameter
Sound and vibration
The noise and vibration values have been developed
with a standardised measurement process.
Sound pressure level L
Sound power level L
wA
Uncertainty K
WA
Maximum vibration on right
handle a
h
Maximum vibration on left
handle a
h
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
16 І 124
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
820 mm
6,3 bar
160 l/min
280 l/min
2100 bpm
18 mm
8 mm
86,69 dB(A)
pA
100,7 dB(A)
1,66 dB
15,53 m/s²
16,22 m/s²
1,5 m/s²
Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working or-
der.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Before commissioning

Check the device, all tools and accessory parts for vis-
ible damage before use. Damaged tools shall not be
used.
An adequately powerful compressed air source (e.g.
compressor) of 3 to 6.3 bar and a suction performance
of at least 160 l/min is required for the air supply for the
compressed air device.
mAttention! Danger of device damage if the operating
pressure at the device is more than 6.3 bar.
The following compressors are recommended:
24 litres Light work
50 litres Moderate work
100 litres and more Heavy work
Connection
• We recommend connecting a maintenance unit with
a mist lubricator between the compressed air source
and the compressed air tool (not included in the
scope of delivery). Alternatively, add 3-5 drops of oil
into the compressed air connection each time before
starting the compressed air tool.
• The compressed air hose (not included in the deliv-
ery) should not be longer than 15 metres and should
have an internal diameter of at least 8 mm in order to
minimise pressure loss.
• m Attention! Danger of tripping due to improperly
laid compressed air hoses! Lay the compressed
air hoses such that they do not cross paths and
such that they are flat to the floor. Always lay the
compressed air hoses such that there is a rea-
sonable amount of spare hose length in the work
area.
• Note that the line oiler should be attached at the same
floor level or storey as the working device.
Lubrication
• If the insertion end (hex.) of the tool being used is
lightly moistened with oil after operation, the oiler is
correctly set.
• If oil emerges at the valve on the actuation body or
if it runs along the tool attachment, the oil quantity is
set too high.
• Adjust oil quantity and top up oil
• Please use special compressed air oil - important:
Use only resin-free oil!