Instructions For Correct Use; Fitting Blades; Transporting The Machine - Nuova Mondial Mec MANTA Série Mode D'emploi

2] If the power socket and the plug on the machine are of different types, have the machine plug replaced with a suitable
one by a qualified technician.
3] Never allow the machine to be used by children or by incapable or mentally disabled persons. Keep all extraneous
persons at least 5 metres away from the work area.
4] Remove the plug from the power socket when the machine is not being used, when it is being cleaned and when
blades are being mounted or dismounted.
5] Ensure that the machine is placed on a flat surface. This will increase its stability.
6] Do not use the machine in conditions of insufficient lighting.
7] Do not use the machine in the rain or in the vicinity of inflammable or explosive materials.
1] The control for switching the machine on is on the motor head, in an easily accessible position (REF.37 EUROPE).
2] This machine must be used only for the purpose for which it has been made, namely the cutting of marble, granite,
brick products, ceramic tiles, etc. Any other use is to be considered improper, and consequently dangerous.
The manufacturer cannot be held responsible for any damage to persons or things caused by improper,
incorrect or unreasonable use of the machine.
3] Do not use the machine if a malfunction has occurred. In this case the machine should be switched off and should not
be tampered with. Consult your local dealer for advice on any necessary repairs. The dealer will provide you
with authorized technicians and original spare parts if required. Failure to respect this procedure may impair
the safety of your machine and be a risk for the operator. The responsibility of the manufacturer will
consequently be invalidated.
4] Do not use the machine without the blade guard (REF.22), as this protects against fragments of waste that might be
expelled.
5] Regularly check the condition of power cables and have them replaced if they are damaged. They should be replaced
by a qualified technician.
6] Operator position: PHOTO 2 PAGE 3.
7] On EUROPE versions, the ON button is green and is inset above the projecting red STOP button.
1] Set the locking rings and carriage end-of-travel stops (REF.6) according to the diameter of the blade being used. This
is essential to prevent the blade from coming into contact with the base of the machine. PHOTO 3, 4 PAGE 3
2] Before mounting or replacing the blade, ALWAYS REMOVE THE PLUG FROM THE POWER SOCKET.
3] Fill the tank with water until the pump is completely covered. This will prevent it from overheating and seizing up.
4] To mount a blade, remove the front section of the blade guard (REF.21/22). PHOTO 5, 6 PAGE 3
5] Raise the motor carriage by moving the handwheel in a clockwise direction (REF.1). PHOTO 7 PAGE 3
6] Unscrew the blade locknut (left-hand thread REF.29) with the service tools provided PHOTO 8 PAGE 3
7] Remove the counterflange (REF.28) and mount or dismount the blade (use only diamond blades or special blades for
the material to be cut). PHOTO 9 PAGE 3
8] Replace the counterflange and the nut (REF.29/28) and the front section of the blade guard (REF.22).
9] Before cutting, check that the two locking levers on the shoulders are correctly tightened (REF.13) and that the knobs
or bolts of the legs (REF.18) are tight. PHOTO 10 PAGE 3
10] For slanted cuts, slacken the two levers (REF.13). Raise the motor carriage (section 5, page 8), lift the motor head
(see photo) and move it to the desired angle. Then retighten the two levers (REF.13). PHOTO 11 PAGE 3
Four carrying handles are provided for manual transport of the machine. These are located beneath the tank (REF.19).
Proceed as follows.
1] Raise the motor carriage (see photo 11 page 3).
Nuova Mondial Mec S.R.L.
MANUALE SERIE MANTA
MANTA SERIES MANUAL
!!!ATTENTION!!!
DO NOT TOUCH THE BLADE WHILE IT IS MOVING!

INSTRUCTIONS FOR CORRECT USE

FITTING BLADES

TRANSPORTING THE MACHINE

pag.17