Denon DN-S3500 Mode D'emploi page 13

Adjusting the pitch and Key Adjust
• With the Pitch slider you can adjust the playback
speed (Pitch).
• If you would not prefer to change key of sound, use
the Key Adjust function.
Push the #4
PITCH button to
PITCH
PITCH LED lights up.
1
RANGE
Pitch decreases
Move the #3 Pitch Slider to adjust
2
the pitch. The current pitch setting
0
is displayed on the display.
Pitch increases
DN-S3500 has six pitch ranges, 4%, 10%,
16%, 24%, 50% and 100%.
When the #4
RANGE button PITCH
is pushed for more than 1 sec,
the pitch range can be selected
RANGE
with the @7 PARAMETERS knob.
• When the @7 PARAMETERS knob is pushed
the pitch range is entered and the pitch range
3
selection mode is cancelled.
PARAMETERS
PUSH ON/OFF
TRACK SEARCH
NOTE:
Only a max of 16% range for MP3 discs.
KEY ADJUST ON
When the #5 KEY ADJUST button is pushed,
4
-1
the Key Adjust function is turned on and lights
up "KEY ADJ." in the display.
KEY ADJUST OFF
4 When the #5 KEY ADJUST button is pushed
-2
again, the Key Adjust function is turned off.
Pitch Bend
• With PITCH BEND function you can change pitch
temporary. DN-S3500 has two ways for this function
PITCH BEND buttons and Scratch Disc.
PITCH BEND +/– buttons
• Push the #1 PITCH BEND – or #2 + button for
momentary change of pitch.
While holding these
buttons down, the pitch
1
continues to change up
to the limitation.
PITCH BEND
• After releasing the
PITCH BEND buttons,
playback pitch returns to slider setting.
When the Platter source is set
to MAIN and the Platter is
turning, playback of the Main
source can be slowed
temporarily by lightly pressing
2
!0 Scratch Disc or PLATTER.
In addition, playback can be quickened
temporarily by pushing Scratch Disc or
PLATTER in the direction in which the Platter is
turning.
Scratch Disc
• When the Platter source is
set to BEND, the playback
speed can be changed by
turning !0 Scratch Disc during
playback. The display will
3
indicate "Pitch Bend" during this mode.
• The pitch increases gradually when the
Scratch Disc is turned clockwise and
decreases when turned counterclockwise.
• When you stop turning the Scratch Disc, the
playing speed returns to the previous pitch.
Relay playback
• Relay Play function is a useful mode to continue
playback between two DN-S3500s.
• Connect the MEMO IN/OUT terminals between two
DN-S3500s.
A2 B
EXIT/
B TRIM
RELOOP
CONT. T T
FILE SEARCH
MODE
RE
PARAMETER P P S
PUSH ON/OFF
Start Relay Play
q Push
the RELAY
button for more than
1 sec to enable
Relay play mode.
You can set Relay
play mode as below.
• In the single play mode, when the one
1
player's playback reaches end of track,
another DN-S3500 starts playing.
• In the continuous play mode, when all
tracks on one player are finished, another
DN-S3500 starts.
• The discs in two DN-S3500s can be
played alternately by setting both DN-
S3500 to the relay play mode.
Stop Relay Play
w When the RELAY
button is pushed for
more than 1 sec
2
while in the relay
play mode, the relay
play mode is turned
off.
7
ENGLISH
Power on play
• When "POWER ON PLAY" is set to "ON" at "⁄5
PRESET (10)", playback starts from the first track on
the disc when the power is turned on.
q, w
CONT.
/SINGLE
RELAY
CONT.
/SINGLE
RELAY
ENGLISH