Bosch GOP 18V-28 Professional Notice Originale page 21

OBJ_BUCH-2789-002.book Page 21 Thursday, June 30, 2016 9:37 AM
Accessory
BIM plunge cut
saw blade, wood
and metal
TC plunge cut saw
blade, metal
BIM plunge cut
saw blade, wood
and metal
HCS plunge cut
saw blade, wood
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/
accessory.
To do so, open the SDS lever 7 all the way. The application
tool/accessory will be ejected.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 9) in such a manner on the tool holder 8 that the
offset faces downward (see illustration on the graphics page;
marking on the application tool/accessory is readable from
above).
When doing so, place the application tool/accessory in a posi-
tion which is convenient for the job at hand. Twelve different
positions are possible, each offset by 30°.
Press the application tool/accessory in the required position
firmly onto the clamping jaws of the tool holder until it is auto-
matically locked.
 Check the tight seating of the application tool/accesso-
ry. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Mounting and Adjusting the Depth Stop
The depth stop 16 can be used when working with segment
and plunge cut saw blades.
If required, remove an already mounted application tool/
accessory.
Bosch Power Tools
Material Application
Softwood, Fast, deep plunge cuts in wood and metal;
Hardwood, example: quick cutting of wood containing nails, deep
Veneered panels, plunge cuts in laminated panels and precise shortening of
Plastic-laminated panels, door frames
Non-hardened nails and
screws
Stainless steel (Inox), Fast, deep plunge cuts in severely abrasive materials or
Screws and nails, metal;
Epoxy resin, example: fast cutting of kitchen front covers, easy cutting
Glass fibre reinforced through hardened screws, nails and stainless steel
plastics,
Fibreglass,
Plasterboard,
Porous concrete
Wood, Fast, deep plunge cuts in wood, abrasive wooden materials
Abrasive wooden materi- and plastics;
als, example: fast cutting of non-ferrous metal pipes and pro-
Plastics, files with smaller dimensions, easy cutting of non-hardened
Hardened nails and nails, screws and steel profiles with smaller dimensions
screws,
Non-ferrous metal pipes
Softwood, Fast, deep separating and plunge cuts; also for sawing
Dowels, close to edges in corners and hard to reach areas;
Tenons, example: deep plunge cut in softwood for installing a venti-
Furniture components lation grid
Slide the depth stop 16 in the required work position all the
way over the tool holder 8 onto the collar of the power tool.
Allow the depth stop to engage. Twelve different positions are
possible, each offset by 30°.
Set the required working depth. Press shut the clamping lever
15 of the depth stop in order to fix the depth stop.
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate 13 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 14, free the Velcro back-
ing of the sanding plate 13 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 14 flush alongside one edge of the
sanding plate 13, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 14, grasp it at one of the tips and
pull it off from the sanding plate 13.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
English | 21
1 609 92A 3BT | (30.6.16)