Waring Commercial MX1300XTX Manuel D'utilisation page 5

RESTORING FACTORY-SET BEVERAGE STATIONS
1. To restore factory-set default beverage stations, press both
Speed Up and Speed Down
PROGRAM.
2. Press button. LCD will prompt RESTORE DEFAULT PROGRAMS.
3. Press button to confirm and save. The LCD will display the logo for
3 seconds.
4. The unit will return to standby mode and the LCD will prompt PRESS
ANY BUTTON TO BLEND.
NOTE: The Stop
key will abort this process at any point before
restoring default programs is confirmed.
DRINK COUNTER
Your reprogrammable blenders are equipped with a drink counter to keep
track of daily drink totals and total drink counts for your machine. To display
the counts, hold program buttons
Your display will read:
DAILY COUNT XXXX
TTL COUNT XXXXX
Daily Count will display the numbers of drinks mixed per day. Total Count
is the accumulation of all drinks made since first use of the blender.
The Daily Count can be reset by holding in program buttons
simultaneously for 3 seconds then, pressing (ON/OFF) button for 3 seconds.
Daily Count will reset to zero and Total Count will remain unchanged.
If Total Count needs to be reset, call your nearest Waring authorized service
facility for information.
NOTE: Use of the PULSE features will not add to the daily or total drink
counts.
RESETTING THERMAL PROTECTION
• Your blender is equipped with an automatic reset function to protect the
motor from overheating.
• If you blender stops running under heavy use, turn the power switch to
Off and unplug the power cord. Empty the blender container of all
its contents and allow between 5 and 30 minutes for the motor to
cool down.
• Plug the power cord back into the outlet and continue blending.
• If your blender does not function properly following this procedure,
discontinue use and contact a certified Waring Customer Service Center.
buttons. LCD will prompt ADD NEW
& simultaneously for 3 seconds.
&
8
IMPORTANT - HOT BLENDING INSTRUCTIONS
To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.
• Hot materials are those that are 100°F (38°C) or hotter.
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece container lid before
starting motor (this will allow venting of the rapidly heated and expanded
air inside the container when blender is running).
• Always start blending on lowest speed setting, and then progress to
desired speed.
• Never stand directly over blender when it is being started or while it
is running.
SOUND ENCLOSURE (for MX1500XTX Version)
Your MX1500XTX/MX1500XTP/MX1500XTS blender is equipped with a
heavy-duty polycarbonate sound enclosure to reduce noise level while
blending. This sound enclosure is removable and dishwasher safe.
To remove the sound enclosure, follow these steps:
1. Open sound enclosure and remove blender container.
2. Remove front portion of sound enclosure by disengaging both sides at
the pivot point.
3. Remove rubber jar pad.
4. Remove 3 screws from blender base and remove sound enclosure.
NOTE: To replace sound enclosure, follow above steps in reverse.
TURNING OFF YOUR BLENDER
Whether your blender is in standby mode, new programming mode, or
the motor is running, pressing the On/Off
from running and will turn the power off. The LCD display will turn off.
NOTE: All programs and current settings will be restored next time you
turn unit on.
CLEANING AND SANITIZING INSTRUCTIONS
THE BLENDER CONTAINER MUST BE CLEANED AND DRIED AFTER EACH
USE ACCORDING TO THE FOLLOWING INSTRUCTIONS. FAILURE TO DO
SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL TO COLLECT ON
THE INTERNAL SEALS OF THE BLADE ASSEMBLY, RENDERING THEM
INEFFECTIVE.
• Wash, rinse, sanitize and dry container prior to initial use and whenever it
will not be used again within a period of one hour.
• Wash and rinse container after each use.
button will stop the unit
9