Milwaukee 2630-20 Manuel De L'utilisateur page 4

•
Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
FUNCTIONAL DESCRIPTION
2
1
15
14
13
12
11
21
1. Front handle
2. Lock-off button
3. Trigger
4. Handle
5. Lower guard lever
6. Shoe
7. Lower guard
8. Lower guard arrow
9. Blade bolt
10. Blade flange
11. Blade
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
UL Listing for Canada and U.S.
C US
3
4
7
8
9
10
16
12. Rip fence slot
13. Sight line
14. Rip fence adjusting knob
15. Upper guard
16. Wrench
17. Spindle lock button
18. Bevel pointer
19. Bevel adjusting knob
20. Bevel scale
21. Depth adjusting lever
Cat. No. ..................................................... 2630-20
Volts.............................................................. 18 DC
Battery Type .................................................M18™
Charger Type................................................M18™
Recommended Ambient
Operating Temperature ......................0°F to 125°F
No Load RPM ..................................................3500
Blade Size ..................................................... 6-1/2"
Arbor ................................................................. 5/8"
Depth of Cut at 90° ................................. 0 to 2-1/8"
Depth of Cut at 45° ............................... 0 to 1-9/16"
WARNING
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
To insert the battery, slide the pack into the body
5
of the tool. Make sure it latches securely into place.
WARNING
may be hazardous.
Select a blade appropriate for your application. Refer
6
to the "Accessories" section for a list of blades to be
used for the proper applications of this tool.
Always use sharp blades. Dull blades tend to over-
load the tool and increase the chance of KICKBACK.
Only use thin kerf blades with a maximum safe oper-
17
ating speed greater than the no load RPM marked on
the tool's nameplate. Read the blade manufacturer's
18
instructions before use. Do not use any type of abra-
sive cut-off wheel or dry diamond cutting blades. Use
the correct blade type for your application. Using the
19
wrong blade may result in reduced performance or
damage to the blade. Do not use blades that are
20
cracked or have broken teeth. Do not sharpen ferrous
metal cutting blades; see the blade manufacturer's
recommendations regarding sharpening.
Checking the Operation of the Lower Guard
Check the operation and condition of the lower guard
lever. If the guard and the lever are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a buildup of debris.
1. Remove battery pack before checking the lower guard.
2. Place the tool on its side.
NOTE: This procedure will not show proper lower
guard operation if the tool is not on its side.
3. Grasp the lower guard by the sides and push it all
the way back into the blade housing.
4. Release the lower guard.
• If the guard immediately springs back into place, it is
working correctly and you may continue with use.
• If the guard does not immediate spring back
into place, clean the upper and lower guards to
remove all chips and debris. Then, check
the operation again by starting with step 1.
• If the guard still does not immediately spring back
into place, contact a MILWAUKEE service facility
for repairs.
4
SPECIFICATIONS
ASSEMBLY
Recharge only with the charger
specified for the battery. For spe-
Always remove battery pack before
changing or removing accessories.
Only use accessories specifically
recommended for this tool. Others
Selecting Blade