Télécharger Imprimer la page

Remington EL-8 Manuel D'utilisation Et D'entretien page 19

Publicité

Les langues disponibles

Les langues disponibles

OPERATING CHAIN SAW
Continued
LIMBING A TREE
WARNING: Avoid kickback. Kick-
back can result in severe injury or death.
See Kickback, page 3, to avoid risk of
kickback.
WARNING: When cutting limb that is
under tension, use extreme caution. Be
alert for wood springing back. When
wood tension is released, limb could
spring back and strike operator causing
severe injury or death.
Limbing is removing branches from a fallen tree.
Make sure your footing is firm. Keep feet apart. Di-
vide your weight evenly on both feet. Do not remove
larger limbs under tree that support log off ground.
Remove each limb with one cut (see Figure 14). Clear
cut limbs from work area often. This will help main-
tain a safe work area.
Make sure you start your cut where limb will not
pinch saw during cutting. To avoid pinching, start
cut on freely hanging limbs from above limb. Start
cut on limbs under tension from under limb. If pinch
occurs, turn saw off, lift limb, and remove saw.
BUCKING A LOG
WARNING: Avoid kickback. Kick-
back can result in severe injury or death.
See Kickback, page 3, to avoid risk of
kickback.
WARNING:
• If on slope, make sure log will not roll
down hill. Secure log by using wooden
stakes. Drive wooden stakes into
ground on downhill side of log. Stand
on uphill side of log while cutting. Log
may roll after cutting.
• Never try cutting through two logs at
same time. This could
increase the risk of kickback.
• While cutting log, never hold log with
your hand, leg, or foot.
• While cutting log, never allow another
person to hold log.
• Turn off and unplug saw before mov-
ing from one place to another.
107705
Bucking a log is cutting a log into sections. Make sure
your footing is firm. Keep feet apart. Divide your weight
evenly on both feet. When possible, raise log or section
off ground. Do this by using limbs, logs, chocks, etc.
When cutting through log, maintain control by re-
ducing cutting pressure near end of cut. Do not relax
your grip on chain saw handles. Do not let moving
chain touch ground. Ground will dull moving chain.
After cutting through log, release trigger to turn saw
off before moving saw.
Follow directions below to buck a log.
Entire Length Of Log On Ground
Cut log from top (see Figure 15).
Log Supported On One End
1. Make first cut on underside of log (see Figure 16).
Use top of guide bar to make this cut. Cut 1/3
through diameter of log. This cut will keep sec-
tion from splintering when cut.
2. Make second cut directly above first cut. Cut
down to meet first cut. This cut will keep log
from pinching guide bar and chain.
Log Supported On Both Ends
1. Make first cut from above log (see Figure 17).
Cut 1/3 through diameter of log. This cut will
keep section from splintering when cut.
2. Make second cut on underside of log, directly
under first cut. Use top of guide bar to make this
cut. Cut up to meet first cut. This will keep log
from pinching guide bar and chain.
TRIMMING A TREE (PRUNING)
WARNING: Avoid kickback. Kick-
back can result in severe injury or death.
See Kickback, page 3, to avoid risk of
kickback.
WARNING: Do not operate chain
saw while
• in a tree
• on a ladder or any other unstable sur-
face
• in any awkward position
You may lose control of saw causing
severe injury.
WARNING: Do not cut limbs higher
than your shoulders.
CAUTION: Seek professional help if
facing conditions beyond your ability.
19
Continued
www.desatech.com

Publicité

loading

Ce manuel est également adapté pour:

107624-01107624-02107625-01107625-02111174-01