Titan IMPACT 640 Notice D'utilisation page 7

Main Screen
The Main Screen is the default screen
for the control system at sprayer startup.
Pressing the #2 key switches between PSI, Bar, and MPa units
of measure. Press the #1 key to scroll through the remaining
menu screens.
volume Pumped Screen
The Volume Pumped screen shows the
total number of gallons or liters sprayed
by the sprayer.
To select the Volume Pumped screen,
press the #4 key.
Job volume Screen
The Job Volume screen allows the user
to reset a gallon counter to track usage
on specific jobs.
To select the Job Volume screen, press
the #4 key.
unit Serial # Screen
The Unit Serial # screen shows the
sprayers serial number.
To select the Unit Serial # screen, press
the #4 key.
Timers Screen
The Timers screen shows the total time
the sprayer has been turned on as well
as the total time the sprayer has been running (pumping).
To select the Timers screen, press the
#4 key.
Job Timers Screen
The Job Timers screen allows the user
to reset the "ON TIME" and "RUN TIME"
to track time on specific jobs.
To select the Job TImers screen, press
the #4 key. "JOB ON" screen will
appear. Press #3 to reset. Press #1 to
continue to "JOB RUN" screen. Press
#3 to reset. Press #1 to scroll through
the remaining menu screens.
Service Time Screen
The Service Time screen allows the user
to set a service time interval (in hours).
Below the set time, the screens shows the current amount of
hours on the sprayer since the last activation of the service timer.
To select the Service Timer screen, press the #4 key.
To set the service time, press the #2
(up) and/or the #3 (down) keys to the
desired time (run hours will increase/decrease in increments of 1
for each time you press a key).
When the service time interval is set and met by the run hours,
the display will show a "Service Required" screen. The pump
will remain functional. To return to the Main Screen, press the
#1 key. Doing so will reset the "Service @" and "Run Hours"
displayed on the Service Screen back to 0.
© Titan Tool Inc. All rights reserved.
Security code Screen
SET PSI 3000
The Security Code screen allows the
ACTUAL PSI 2950
user to set a four digit security code
to prevent unauthorized use of the sprayer. If a security code
has been set, the control system display will ask for the code at
startup. If the correct code is entered, the display will show the
Main Screen and the sprayer will operate. If the wrong code is
entered, the display will continue to ask for the correct code and
the sprayer will be disabled. To set or change the security code,
press the #2 key.
VOLUME PUMPED
MENU-1 SELECT-4
GALLONS X
MENU-1
Enter the old security code number to
JOB VOLUME
access the screen that allows the code
MENU-1 SELECT-4
change. If the wrong code is entered, the display will continue
to ask for the correct code and the security code cannot be
JOB GAL XXXX
changed.
MENU-1 RESET-3
Enter the new security code. Once the
new code is entered, the display will
automatically ask that the new code be
re-entered for verification. If the same
UNIT SERIAL #
new code is re-entered, the display will
MENU-1 SELECT-4
confirm that the new code has been
accepted and return to the Main Screen.
SER # XXXXXXXXXX
MENU-1 If the new code is re-entered incorrectly, the display will return
to the "Enter New Code Number" screen and the process will
repeat.
If you forget or misplace your security code, you can call Titan
customer service for assistance.
TIMERS
MENU-1 SELECT-4
ON TIME XXXX
RUN TIME XXXX
Prime Screen
JOB TIMERS
The Prime screen appears when the
MENU-1 SELECT-4
pressure control knob is set at the "MIN"
setting.
JOB ON X
MENU-1 RESET-3
Rapid clean Screen
JOB RUN X
MENU-1 RESET-3
The Rapid Clean screen appears when
the pressure control knob is set at the
RAPID CLEAN position and the PRIME/SPRAY valve is in the
PRIME position.
SERVICE TIME
MENU-1 SELECT-4
SERVICE @ XX
RUN HOURS XX
7
NOTE: If the sprayer is new, no security code is set and
the Main Screen will appear at startup. When
setting a security code for the first time, the
"Enter Old code Number" screen will appear,
and you will need to enter "1111".
NOTE: To inactivate the anti-Theft Digital Lockout
security function, enter "1111" at the "Enter New
code Number" screen (this is the default code
that leaves the sprayer unlocked). as a result,
the Main Screen will appear at sprayer startup.
NOTE: If there is no action at any menu screen for 30
seconds, the display will go back to the Main
Screen.
SECURITY CODE
MENU-1 CHANGE-2
ENTER OLD CODE
NUMBER XXXX
ENTER NEW CODE
NUMBER XXXX
RE-ENTER NEW
NUMBER XXXX
NEW CODE NUMBER
ACCEPTED
PRIME
RAPID CLEAN
English