Berner BSD-HD-1 Mode D'emploi page 11

ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of chil-
u
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools and accessories. Check
u
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unex-
pected situations.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Safety Warnings for Screwdrivers
Hold the power tool by insulated gripping sur-
u
faces, when performing an operation where
the fastener may contact hidden wiring or its
own cord. Fasteners contacting a "live" wire
may make exposed metal parts of the power
tool "live" and could give the operator an elec-
tric shock.
Use suitable detectors to determine if utility
u
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
Hold the power tool securely. When tightening
u
and loosening screws be prepared for tempor-
arily high torque reactions.
1 609 92A 53N • 15.4.19
Secure the workpiece. A workpiece clamped
u
with clamping devices or in a vice is held more
secure than by hand.
Always wait until the power tool has come to
u
a complete stop before placing it down. The
application tool can jam and cause you to lose
control of the power tool.
Products sold in GB only:
Your product is fitted with an BS 1363/A ap-
proved electric plug with internal fuse (ASTA ap-
proved to BS 1362).
If the plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in
its place by an authorised customer service agent.
The replacement plug should have the same fuse
rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inser-
ted into a mains socket elsewhere.
Product Description and
Specifications
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or ser-
ious injury.
Please observe the illustrations at the beginning
of this operating manual.
Intended Use
The power tool is intended for screwing in and
loosening screws.
English
Product Features
The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1) Screwdriver bit
(2) Stop sleeve
(3) Adjusting sleeve for screw depth stop
(4) Screw depth stop
(5) Belt clip
(6) Lock-on button for on/off switch
(7) On/off switch
(8) Rotational direction switch
(9) Handle (insulated gripping surface)
(10) Universal bit holder
A) Accessories shown or described are not included
with the product as standard. You can find the com-
plete selection of accessories in our accessories
range.
English
English
English
A)
A)
English | 11