Cardin Elettronica SL Série Mode D'emploi page 16

INSTRUCTIONS FOR POSITIONING THE UNIT
- The geared motor unit has been assembled in the fac-
tory to be fitted to the LEFT SIDE of the gate (internal
view). To install the motor to the RIGHT of the gate
set dip 8
MANUAL MANOEUVRE WITH THE MOTOR RELEASED
Manual release is to be carried out with the motor stopped. To release the gate
use the manual release key supplied with the unit. The key should be kept in
an easily accessible place.
To release the unit
1. Rotate the lock protection disk, insert the key,
rotate it half a turn anticlockwise and lift up the
knob cover.
The knob is now free and can be released.
2. Rotate the knob clockwise until it can turn no more.
Attention: do not force the knob to turn further
than its travel limit. The gears are now released
and the gate can be moved manually.
To relock the unit
1. Rotate the knob anticlockwise and move it back to the blocked position.
2. Close the knob cover, rotate the key clockwise and rotate the lock pro-
tection disk cover.
The gears are now blocked and the gate is ready for use. Once the
system has been reset store the key in a safe place.
Attention! Never use the manual release mechanism while
the gate is in operation. If you release the gate and then give a
movement command the following symbol will appear on the
display .
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
9
A
ELECTRONIC PROGRAMMER
Electronic programmer for a dc motor with an incorporated radio receiver card,
which allows the memorisation of 300 user codes
The motor rotation speed is electronically controlled, starting slowly and
increasing in speed; the speed is reduced as it nears the travel limit so as to
enable a controlled smooth stop.
CALA: 1:2
Programming is carried out using one button and allows you to set the system,
Description : Prodotti Technocity
awing number : DI0361
Sblocco carter
oduct Code : SL324
the current sensor and the entire gate travel distance.
aft : P.J.Heath Date : 14-02-2005
RDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
The logic carries out position control using an encoder.
The intervention of the anticrush/antidrag sensor during the closing and opening
stages causes a brief (10 cm) travel direction inversion then a block.
7
ON
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
DS1 ON
SCALA: 1:2
Description :
Drawing number :
DI0363
Sblocco motore
Product Code :
SL324
Draft : P.J.Heath Date : 07-02-2002
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Access to the electronic card
Attention! Before opening the cover make sure
that the power has been switched off at the
mains.
positioned on either end of the cover as indicated
in figure 9.
433.92 MHz series transmitters.
programmer, release the gate (manual release mechanism) and
move it manually, checking that it moves smoothly and has no
unusual points of resistance.
indicated by the warning lights pre-flashing for 10 seconds, and by
the symbol
ing
1 2 3 4 5 6 7 8 9
system, which is used to block the motor in emergency conditions;
however this system is not active during the following stages:
- during the first 5 s of an opening stage starting from completely
closed
- during the first 2 seconds of all other movement stages
- when the battery undercharged
Do not therefore attempt to physically block the door during these
stages, otherwise you may risk blowing the motor circuit protec-
power supply to the programmer; reconnect it only after having
re-inserted the fuse.
not exclude the need to install photoelectric cells or other safety
devices which are foreseen by the local standards and regulations
All rights reserved. Unauthorised copying or use of the information contained in
in force.
for positioning the unit
8
batteries must be in good condition: the programmer will lose the
position of the gate in case of blackouts when the batteries are flat,
the alarm will sound and automatic repositioning will take place .
Prodotti Technocity
Check the good working order of the batteries every six months
frequency rated on the data plate conform to those of the mains
supply.
must be installed between the unit and the mains supply.
ends of cables which are to be inserted into the binding posts; use
cables marked T min 85°C and resistant to atmospheric agents.
the wire and the insulating sheath are tightly fastened (a plastic
jubilee clip is sufficient).
Mains power supply connection
A
right of the main circuit board and to the separate 3-way terminal board:
- connect the neutral to binding post N
- connect the earth to binding post
- connect the live to binding post
16
IMPORTANT REMARKS
F1
The presence of the electrical input monitoring system does
The geared motor unit has been assembled in the factory to be
For the correct operation of the programmer the incorporated
Battery check
L
before powering up the
automatic reposition-
F2
instructions
3 mm between the contacts
N
L