Bosch PKS 16 Multi Notice Originale page 19

The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Use a dust extractor when working with stone. The
u
dust extractor must be approved for extracting stone
dust. Use of this equipment can reduce the risks posed
by dust.
Do not allow the chip ejector to come into contact with
u
your hands. You may be injured by rotating parts.
Do not use the saw above the level of your head. Doing
u
so will mean you have inadequate control of the power
tool.
Do not operate the power tool when stationary . It is
u
not suitable for operation with a saw table.
Do not use HSS saw blades. Such saw blades can easily
u
break.
Do not saw any ferrous metals. Hot chips may ignite the
u
dust extractor.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for making straight cuts in wood
with and against the grain, while resting firmly on the work-
piece. With suitable saw blades, you can also saw thin-
walled non-ferrous metals or plastic, such as profiles. With
suitable diamond cutting discs, you can cut tiles without us-
ing water.
The power tool must not be used to cut ferrous metals.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Lock-off switch for on/off switch
(2) On/off switch
(3) Base plate
(4) Unlocking lever for base plate
(5) Slider for preselecting the cutting depth
(6) Protective guard
(7) Viewing window for "Cut Control"
(8) Screw for setting the cutting depth
(9) Dust extraction adapter
(10) Auxiliary gripping surface (insulated)
Bosch Power Tools
(11) Handle (insulated gripping surface)
(12) Spindle lock button
(13) Mounting flange
(14) Circular saw blade
(15) Clamping bolt with clamping flange
(16) Hex key
A)
(17) Dust extraction hose
A)
(18) Pair of screw clamps
(19) 0° cut mark
(20) Chip ejector
A)
(21) Diamond cutting disc
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Handheld circular saw
Article number
Rated power input
No-load speed
Base plate dimensions
Locating bore
Weight according to
EPTA-Procedure 01:2014
Protection class
Max. cutting depth
Max. saw blade diameter
Min. saw blade diameter
Max. base blade thickness
Max. tooth thickness/offset
Min. tooth thickness/offset
Max. diamond cutting disc
diameter
Working with a diamond cut-
ting disc
– Min. cutting disc thick-
ness
– Max. cutting disc thick-
ness
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-5.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 83 dB(A); sound power level 94
dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
English | 19
PKS 16 Multi
PKS 1600 Multi
3 603 CB3 0..
W 400
-1
min 6 400
mm 68 x 233
mm 15
kg 1.9
/ II
mm 16
mm 65
mm 65
mm 1.2
mm 2.0
mm 0.8
mm 65
mm 0.6
mm 1.2
1 609 92A 4FS | (26.11.2018)