Computer Instructions - Christopeit Sport AM 5 Notice De Montage

Computer instructions for 1126
The supplied computer allows the most convenient training. Every value
relevant to training is displayed in a corresponding window.
From the beginning of the training session, the required time, the current
speed, the approximate calorie consumption, the travelled distance ad the
current pulse rate are displayed. All values are counted from zero upwards.
The speed is indicated on the upper display. All other values are indicated
on the lower display.
If you wish to see one value displayed constantly as well as the speed
during training, select this with the „F" key. If you wish to see these values in
constant alternation, select the „SCAN" function. The display then changes
from one function to the next at intervals of approx. 6 seconds.
The computer is switched on by briefly pressing the F- key or simply by
beginning training. The computer begins to register and display all values.
To stop the computer, just stop training. The computer stops all
measurements and retains the last attained values. The last attained values in
the functions TIME, CALORIES and KM are stored and training can continue
with these values when training is resumed.
The computer switches of automatically approx. 4 minutes after training
is stopped. All values attained until that time are stored and are displayed
again when training is resumed. It is then possible to continue training from
these values or to reset all functions to zero using the L- key.
Displays:
1. „SPEED" (KM/H) display:
The current speed is displayed in kilometres per hour. It is not possible to
specify a particular value using the „E" key. The values last attained by this
function are not stored. (Limit of the display: 99.9 km/h.)
2. „TIME" (ZEIT) display:
The currently required time is displayed in minutes and seconds. It is possible
to specify a particular value using the „E" key. If a particular time
has been specified, the remaining time is displayed. When the specified
value is attained, this is indicated by an acoustic signal. The values last
attained by this function are stored. (Limit of the display: 99.59 minutes.)
3. „DIST (KM)" display:
The current status of the travelled distance is displayed. It is possible to
specify a particular value using the „E" key. If a particular distance has been
specified, the remaining distance is displayed. When the specified value is
attained, this is indicated by an acoustic signal. The values last attained by
this function are stored. (Limit of the display: 999 km.)
4. „CALORY" (CAL) display:
The current status of the consumed calories is displayed. It is possible to
specify a particular value using the „E" key. If a particular consumption
has been specified, the remaining number of calories to be consumed
is displayed. When the specified value is attained, this is indicated by an
acoustic signal. The values last attained by this function are stored. (Limit
of the display: 999 calories.)
5. „KM TOTAL" (ODO) display:
The current status of the travelled kilometres of all previous training sessions
including current training session is displayed. A particular value cannot be
speci. ed. The values last attained by this function are not stored. (Limit of
the display: 9.999 km.)
6. „PULSE" display:
The current pulse rate is displayed in beats per minute. It is not possible to
specify a particular value using the „E" key.
The values last attained by this function are not stored. (Limit of both displays:
40 – 240 pulse beats per minute.)
Note:
For pulse measurement, the two contact surfaces of the pulse measuring
handle unit (4) must be gripped simultaneously. The contact surfaces should
be located centrally in the palms of the hands.
7. „SCAN" function:
If this function is selected, the current values of all functions are displayed
successively in a constant sequence approx. every 5 seconds.
Keys:
1. „F" key:
Pressing this key once briefly makes it possible to change from one function
to another, i.e. the respective functions can be selected for which entries
can be made using the „E" key. The currently selected function is indicated
by an icon in the respective window.
2. „E" key:
By pressing this key once, it is possible to specify values step by step in the
respective functions. For this, the desired function must firstly be selected
using the „F" key.
Holding the key pressed activates faster running, which can be stopped
by pressing the key again. When training begins, the specified values are
then counted down to zero.
3. „L" = Delete:
When this key is pressed briefly, the values chosen with the „F" key are
reset to zero. If the key is held longer (approx. 3 seconds), all last attained
values are deleted with the exception of the values in the „KM TOTAL"
display.
18