Bosch GBH 36 V-LI Plus Professional Notice Originale page 18

OBJ_BUCH-283-014.book Page 18 Thursday, August 17, 2017 3:16 PM
18 | English
To remove the battery 11:
– Push the battery against the base of the power tool (1.)
and at the same time press the battery unlocking button 18
(2.).
– Pull the battery out of the power tool until a red stripe be-
comes visible (3.).
– Press the battery unlocking button 18 again and pull out
the battery completely.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
20 indicate the charge condition of the battery 11. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– Push button 21 to indicate the charge condition (also pos-
sible when the battery is removed). The battery charge-
control indicator automatically goes out after approx.
5 seconds.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 21, then the bat-
tery is defective and must be replaced.
During the charging procedure, the three green LEDs light up
one after the other and briefly go out. The battery is fully
charged when the three green LEDs light up continuously. The
three LEDs go out again approx. 5 minutes after the battery
has been fully charged.
Auxiliary Handle
 Operate your machine only with the auxiliary handle
16.
Changing the position of the auxiliary handle
(see figure B)
The auxiliary handle 16 can be set to any position for a secure
and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 16 in counter-
clockwise direction and swivel the auxiliary handle 16 to
the desired position. Then retighten the bottom part of the
auxiliary handle 16 by turning in clockwise direction.
Pay attention that the clamping band of the auxiliary handle is
positioned in the groove on the housing as intended for.
1 609 92A 3XU | (17.8.17)
Selecting Drill Chucks and Tools
For hammer drilling and chiselling, SDS-plus tools are re-
quired that are inserted in the SDS-plus drill chuck.
For drilling without impact in wood, metal, ceramic and plas-
tic as well as for screwdriving, tools without SDS-plus are
used (e.g., drill bits with cylindrical shank). For these tools, a
keyless chuck or a key type drill chuck are required.
Inserting/Removing the Key Type Drill Chuck
(GBH 36 VF-LI Plus)
To work with tools without SDS-plus (e.g., drills with cylindri-
cal shank), a suitable drill chuck must be mounted (key type
drill chuck or keyless chuck, accessories).
Mounting the Key Type Drill Chuck (see figure C)
– Screw the SDS-plus adapter shank 24 into a key type drill
chuck 23. Secure the key type drill chuck 23 with the se-
curing screw 22. Please observe that the securing
screw has a left-hand thread.
Inserting the Key Type Drill Chuck (see figure C)
– Clean the shank end of the adapter shank and apply a light
coat of grease.
– Insert the key type drill chuck with the adapter shank into
the tool holder with a turning motion until it automatically
locks.
– Check the locking effect by pulling the key type drill chuck.
Removing the Key Type Drill Chuck
Capacity
– Push the locking sleeve 5 toward the rear and pull out the
≥2/3
key type drill chuck 23.
≥1/3
Removing/Inserting the Quick Change Chuck
<1/3
(GBH 36 VF-LI Plus)
Reserve
The SDS-plus quick change chuck 2 can easily be replaced
against the quick change keyless chuck 1 provided.
Removing the Quick Change Chuck (see figure D)
– Pull the lock ring for the quick change chuck 6 toward the
rear, hold it in this position and pull off the SDS-plus quick
change chuck 2 or the quick change keyless chuck 1 to-
ward the front.
– After removing, protect the replacement chuck against
contamination.
Inserting the Quick Change Chuck (see figure E)
 Use only model-specific original equipment and pay at-
tention to the number of identification grooves 26. On-
ly quick-change chucks with two or three identification
grooves are permitted. When an unsuitable quick-change
chuck is used, the application tool could fall out during op-
eration.
– Before inserting, clean the quick change chuck and apply a
light coat of grease to the shank end.
– Grasp the SDS-plus quick change chuck 2 or the quick
change keyless chuck 1 completely with your hand. Slide
the quick change chuck with a turning motion onto the drill
chuck mounting 25 until a distinct latching noise is heard.
– The quick change chuck is automatically locked. Check the
locking effect by pulling the quick change chuck.
Bosch Power Tools