Publicité
OBJ_BUCH-3327-001.book Page 7 Friday, November 24, 2017 9:54 AM
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate
of material removal, different sanding sheets are available:
For the working of all wooden
materials
For coarse-sanding, e. g. of rough,
unplaned beams and boards
For face sanding and planing small
irregularities
For finish and fine sanding of hard
woods
For the working of paint/enamel
coats or primers and fillers
For sanding off paint
For sanding primer
For final sanding of primers before
coating
Dust/Chip Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Bosch Power Tools
Switching On and Off
To start the machine, tilt the On/Off switch 1 toward the right
to the "I" position.
To switch off the machine, tilt the On/Off switch 1 toward the
Grain size
left to the "0" position.
40 – 240
To save energy, only switch the power tool on when using it.
Working Advice
Wait until the machine has come to a standstill before
placing it down.
coarse
40, 60
The removal capacity during sanding is mainly determined by
the selection of the sanding sheet.
medium 80, 120
Only flawless sanding sheets achieve good sanding capacity
and extend the service life of the machine.
fine
180, 240
Pay attention to apply uniform sanding pressure; this increas-
40 – 240
es the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an in-
crease of the sanding capacity, but to increased wear of the
machine and the sanding sheet.
coarse
40, 60
A sanding sheet that has been used for metal should not be
medium 80, 120
used for other materials.
Use only original Bosch sanding accessories.
fine
180, 240
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Cambodia
Robert Bosch (Cambodia) Co., Ltd
Unit 8BC, GT Tower, 08th Floor, Street 169,
Czechoslovakia Blvd, Sangkat Veal Vong
Khan 7 Makara, Phnom Penh
VAT TIN: 100 169 511
Tel.: +855 23 900 685
Tel.: +855 23 900 660
www.bosch.com.kh
English | 7
1 609 92A 407 | (24.11.17)
Publicité
