Yakima 8002116 Mode D'emploi

USE ON FORKS
WITH 100mm HUB
SPACING ONLY.
INSTALL FORK ADAPTER:
Attach the FORK AdApteR while bike is still on the ground.
• Slide the FORK AdApteR between fork drop outs. Slide axle back
through fork dropouts, and through the FORK AdApteR.
• Completely tighten and close the thru-axle lever as you would if
you were installing your front wheel.
FORK AdApteR legs must run parallel with the fork
leg, unless you are running several bikes on your
rack. Conflicting handlebar heights require the FORK
AdApteR to be rotated (maximum of 180°).
ATTACH TO FORK-mOUNTED BIKE RACK
• Check the thru-axle is tight and the FORK Adapter is
securely attached to your fork.
• Attach the FORK AdApteR onto your fork-mounted rack.
(Follow the manufacturer's directions on tightening
down the quick release before driving away.)
Be sure FORK AdApteR and bike
are both mounted securely to your
bike rack before driving.
BEFORE RIDING:
• Check that your thru-axle is tight and
your front brake works properly.
teCHNICAL ASSIStANCe OR
RepLACeMeNt pARtS
Contact your dealer or call (888)925-4621
Monday through Friday,
7:00 AM to 5:00 pM, pSt
IMPORTANT WARNING: IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE.
IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO
OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS PRIOR TO USE,
AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL
OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND
ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE
INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER SUCH AS A QUALIFIED GARAGE OR
AUTO BODY SHOP.
1035811A-1/3
12 x 100 Fork Adapter
REmOvE FRONT WHEEL:
Completely unthread and pull
out the thru-axle skewer.
mAINTENANCE
periodically check for excessive
wear, including rust or cracks.
Replace if cracked or rusted.
ReMOVe ACCeSSORY BeFORe
eNteRING AN AUtOMAtIC CAR
WASH.
K E E P T H E S E
This figure may differ from your fork.
Follow your fork manufacturer's directions for wheel
removal, axle and axle bolt location and tightening.
TO REmOvE FORK ADAPTER
(
do not leave FORK AdApteR attached to your rack.)
• Remove the bike from your rack with the FORK
AdApteR still attached to your fork.
• Set the bike on the ground, open and unthread the
thru-axle.
• Slide out the axle from the FORK AdApteR and
remove the FORK AdApteR.
• Insert your front wheel; securely tighten the thru-axle
before riding.
this product is covered by YAKIMA's "Love It till
You Leave It" Limited Lifetime Warranty.
to obtain a copy of this warranty, go online to
www.yakima.com or email us at
yakwarranty@yakima.com or call (888) 925-4621
I N S T R U C T I O N S !
different manufacturers have
different methods of wheel
removal, follow your fork
manufacturer's directions.
FORK
AdApteR
WARNING:
Be SURe ALL HARdWARe IS
SeCURed ACCORdING tO
INStRUCtIONS. AttACHMeNt
HARdWARe CAN LOOSeN
OVeR tIMe. CHeCK BeFORe
eACH USe, ANd tIGHteN IF
NeCeSSARY.