Operation; Playback; Set The Power To Standby; When Using The Unit As A Power Amplifier - Pioneer A-70DA-K Mode D'emploi

Operation

Chapter 4:
Operation

Playback

Turntable
SACD/CD player
Network audio player
/I STANDBY/ON
SOURCE SOURCE  
STANDBY DIRECT Hi-Bit 32 Up Sampling
 
iPod/iPhone 5V 1A
2 6
Playback
6 6
1 Turn on the power of the playback
component.
2 Turn power ON to the unit.
• If the unit is in the standby mode, press the remote
control's  STANDBY/ON button.
3 Select the source you want to playback.
Select the playback component.
• When using the front panel controls, rotate the
INPUT SELECTOR knob.
iPod dock, etc.
Audio device with
Recording device
iPod
Music>
Extras>
Settings>
balanced output terminals
Shuffle Songs or other device
Backlight
MENU
 

Playback
5 3
• In the case of the A-70DA, if PHONO is selected,
use the CARTRIDGE select switch to designate the
type of cartridge used with your turntable, either
MM () or MC ().
4 Start playback of the component you
selected in step 1.
5 Adjust playback volume with VOLUME
control.
VOLUME
6 Adjust the tone to your preference using
the BASS and TREBLE controls, and
LOUDNESS button.
If the DIRECT button has been set to ON, these controls
are disabled.
Caution
• The BASS, TREBLE, BALANCE, and LOUDNESS
functions do not work for a device connected to the
BALANCED IN terminals.

Set the power to Standby

Press the remote control's  STANDBY/
1
ON button.
The next time you wish to turn on the power, press the
remote control's  STANDBY/ON button.
• If the front panel's /I STANDBY/ON button is
pressed, the power will be turned off. In this case, if
the power is off, pressing the remote control's
 STANDBY/ON button will not turn on the power.
To turn on the power again, press the front panel's
/I STANDBY/ON button.

When using the unit as a power amplifier

When a pre-amplifier is connected to the unit's POWER
AMP DIRECT IN terminals, the unit can be used as a
power amplifier.
1 Press the POWER AMP DIRECT button
on the remote control or front panel of the
unit.
The POWER AMP DIRECT indicator will light.
Caution
• When the POWER AMP DIRECT indicator is
lighted, operations change as follows:
– The unit's front-panel VOLUME, BASS, TREBLE,
and BALANCE controls are disabled. These
adjustments are controlled by the component
connected to the unit's POWER AMP DIRECT IN
terminals.
– The LOUDNESS button and ATTENUATOR
button (A-70DA only) are disabled.
– When the POWER AMP DIRECT indicator is
lighted, sound volume from the unit will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the POWER AMP DIRECT IN
terminals and set it to a low level as appropriate
before turning on the POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the POWER AMP DIRECT IN
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT indicator lights.
– Sound is not produced from the PHONES jack
and LINE 2 OUT terminals.
• For more information, consult the operating
instructions for the component connected to the
unit's POWER AMP DIRECT IN terminals.
Playing music from a digital audio
component
Output the digital audio input to the DIGITAL IN
COAXIAL or OPTICAL terminal.
1 Make a digital input connection.
• See Digital audio input connections on page 7.
2 Switch to the COAXIAL or OPTICAL
input.
Each press of the COAXIAL/OPTICAL button on the
remote control switches the input alternately.
• When using the front panel controls, rotate the
INPUT SELECTOR knob.
• Sound is produced from the LINE 2 OUT terminals.
Note
• Digital signal formats that can be input to this unit
include linear PCM signals with sampling rates and
quantitative bits up to 192 kHz/32 bits (Depending
on the connected device and environment,
operation may not be successful).
04
11
En