Ecoflam MAXFLAM 30 ABMAXFLAM 50 AB Mode D'emploi page 6

EN
Contents
­ Index ­ General warnings ­ Conformity declaration
Overview
Contents
Function
Installation
Start up
Service
Overview
Important notes
Ecoflam burners have been designed and
built in compliance with all current
regulations and directives.
All burners comply to the safety
and energy saving operation
regulations within the standard
WARNING
of their respective performance
range.
The burner must not operate out­
side the working range.
DANGER
The quality is guaranteed by a quality and
management system certified in
accordance with ISO 9001:2008.
The MAXFLAM burners are designed for
the combustion of heavy oil.
The burners comply with
standard EN267. Assembly and
commissioning must be carried
WARNING
out only by authorised
specialists and all applicable
guidelines and directives must
be observed.
Burner description
The MAXFLAM burner is a two-stage,
fully-automatic monoblock type burners.
Burner head is designed to get the lowest
emissions in terms of NOx and unburnt
particles in order to maximize the heat
generator efficiency. Emissions can be
different respect to the ones recorded in
the lab because they depends a lot on the
generator on which the burner is fit.
The installer must comply with compulsory
6 www.ecoflam­burners.com
Technical data
Working diagrams
Dimensions
Index
General warnings
Conformity declaration
Burner description
General safety functions
Siemens LMO 44 control and safety unit
Oil burner pump
Burner assembly
Electrical connection
Checks before commissioning
Heavy oil feeding and suction line
Setting data table - air regulation
Adjusting burner output
Oil pressure regulation - Recording commissioning data
Maintenance
Troubleshooting
Electrical diagrams
Spare parts list
rules. Avoid for instance dangerous
atmosphere or not ventilated rooms.
Packaging and handling
Move the burner still in its packaging using
a trolley or forklift, taking care not to drop it
and elevating it no more than 20cm from
ground level. After having removed the
packaging, check that the contents are in
good condition and correspond with what
was ordered. If in doubt, contact the
manufacturer.
WARNING
If the weight and dimensions do not allow
for manual lifting, ask another operator for
help or use a forklift, harness the burner
using belts if no eyebolts are available.
WARNING
isolating gasket.
The burner must be installed by a
qualified individual.
Use the accessories provided
(flange, gasket, pins and nuts) to
install the burner onto the boiler,
taking care not to damage the
3
Declaration of conformity for oil
burners
4
5
We,
Ecoflam Bruciatori S.p.A.
6
6
declare under our sole responsibility
6
that the heavy oil burners named
7
MAXFLAM
8
conform to the following standards:
9
EN 267
10
EN 55014­1
EN 60335­1
11
EN 61000­6­2
12
These products bear the CE mark in
12
accordance with the stipulations of the
following directives:
13
2014/35/UE Low Voltage Directive
15
2014/30/UE EMC Directive
16
2006/42/EC Machine directive
2011/65/EU RoHS2 directive
16
17
18
71-72
73-75
We can accept no warranty liability
whatsoever for loss, damage or injury
caused by any of the following:
- Inappropriate use.
- Incorrect assembly or repair by the
customer or any third party, including the
fitting of non-original parts.
Provision of the system and the
operating instructions
The firing system manufacturer must
supply the operator of the system with
operating and maintenance instructions on
or before final delivery. These instructions
should be displayed in a prominent
location at the point of installation of the
heat generator, and should include the
address and telephone number of the
nearest customer service centre.
Notes for the operator
The system should be inspected by a
specialist at least once a year. It is
advisable to take out a maintenance
contract to guarantee regular servicing.
420010537801
EN 50156­1
EN 55014­2
EN 60335­2­102
EN 61000­6­3