Clatronic CL 3639 Mode D'emploi page 31

Using the Appliance
Turning unit on / off
• Press the POWER button to turn on the unit. When used for the fi rst
time, the appliance operates in AUTO mode. If operation has been
stopped without disconnecting the plug, all previously set operating
mode and temperature settings will be retained. In that case, the display
will show these settings instead.
• Press the POWER button again to turn off the device.
Indications on the Display
AUTO
Auto mode
Fan speed
Cooling mode
Indication of the desired room temperature or the
hours in case of TIMER operation
°C
Indication of the temperature setting
Indication with TIMER operation
Dehumidifying mode
The unlit segments do not function on this appliance.
Operating modes
Use the MODE button to select one of the following operating modes:
• AUTO
• Cooling
• Dehumidifying
Operating mode "AUTO" (Automatic)
The appliance decides the must suitable operation mode as shown in the
following table:
Room temperature Operating mode
< 23 °C Fan
≥ 23 °C – < 26 °C Dehumidifying
≥ 26 °C Cooling
You can set the speed of the fan. The temperature setting cannot be
changed.
Operating mode "Cooling"
In this operation mode, you can adjust the fan speed and the temperature
as desired. If you want to use the appliance with the fan only but without
compressor, set a temperature higher than the actual room temperature.
Operating mode "Dehumidifying"
• This operating mode does not support any further settings.
• The appliance will change the set temperature automatically to room
temperature minus 2 °C.
• The fan will operate at the lowest speed setting.
• The unit will cool the room and extract the humidity from the air.
Setting the temperature
Use the TEMP + or TEMP − buttons in "Cooling"
temperature. Select a temperature between 16 °C and 31 °C.
Setting the fan
In "Cooling" and AUTO modes you can set the fan speed with 3 differ-
ent settings. Press the SPEED button accordingly.
CL3639_IM
Timer (Automatic timer)
Use the timer function to set the power-on and power-off times of the
device. Select a time between 1 and 24 hours.
Using the timer function for automatic power-on
1. Press the POWER button to turn on the unit.
2. Select the operating mode, temperature and fan speed for the unit to
operate in or at when powered on at the pre-set time.
3. Press the POWER button to turn off the unit.
4. Press the TIMER button. The display shows the previously set opera-
tion mode and the symbol
5. You can set the desired number of hours with the buttons TEMP +
and TEMP −. The setting changes rapidly when you hold down the
respective button. Confi rm your setting with the TIMER button while
the display is fl ashing. Otherwise you will exit the setting mode. In this
case, the setting will not be applied.
Using the timer function for automatic power-off
1. Press the POWER button to turn on the unit.
2. Press the TIMER button during operation. The display also shows the
symbol
3. Set the timer as described in the above item 5.
NOTE:
• Press the TIMER button again if you want to deactivate the TIMER
function.
• You may also cancel the timer function at any time by pressing the
POWER button to turn the unit on / off.
Emptying the water tank
The unit integrates a water tank for collecting condensation. When the
water tank is full, the pilot lamp "WATER FULL" lights up. The display
shows "E2". The compressor switches off in each operation mode. The
fan keeps running independent of this.
CAUTION:
Do not transport the appliance while the water tank is full. Water could
get into the appliance.
For continued operation with the compressor, you must empty the water
Temperature setting
tank. For this, you need a fl oor cloth, a fl at bowl with a capacity for approx.
– – –
1,5 litres of water and the water hose supplied with the appliance.
23 °C
1. Disconnect the mains plug from the wall socket.
2. Place the fl oor towel and the fl at bowl underneath the water outlet. If
25 °C
possible, set the bowl on a lower level than the appliance.
3. Remove the rubber cap and the plug. Keep the parts for later use.
4. Connect the water hose to the water outlet of the appliance. Place the
end of the hose in the bowl.
5. After the water has been discharged, remove the water hose. Close
the water outlet on the appliance again with the plug and the
rubber cap to ensure the condensation water cooling circulation.
Terminating operation
1. Press the POWER button to turn off the unit.
2. Disconnect the mains plug from the wall socket.
• Always disconnect the mains plug from the wall socket
before cleaning!
mode to set the
• Make sure no water enters the openings of the unit
during cleaning. Otherwise this might result in an
electric shock or fi re.
. The number of hours fl ashes.
. The number of hours fl ashes.
Cleaning
WARNING:
15.12.2015
31