Overview Of The Components - Clatronic CL 3639 Mode D'emploi

Handling batteries
WARNING:
• Do not expose batteries to excessive heat such as sunlight, fi re or
similar. There is a risk of explosion!
• Batteries are not toys. Keep away from children.
• Do not open batteries by force.
• Avoid contact with metal objects (rings, nails, screws, etc.). There is a
risk of short circuit!
• A short circuit could cause the battery to heat up excessively or even
to catch fi re, resulting in injuries.
• For your own safety, cover the battery terminals with adhesive tape
during transport.
• In case of battery leakage, make sure not to rub the liquid into your
eyes or mucous membranes. In case of contact, wash your hands
and rinse your eyes with clear water. Seek medical attention if any
discomfort persists.
CAUTION:
• When not using the remote control for a long period of time, remove
the batteries in order to prevent "leakage" of battery acid.
• Different battery types or new and used batteries must not be used
together.
• Do not dispose of batteries along with domestic waste. Return used
batteries to the relevant collection facilities or your retailer.

Overview of the Components

1 Air inlet on the side of the appliance (Filter)
2 Control panel
3 Mains cable
4 Air outlet (fi ns)
5 Exhaust pipe connector
6 Rear side air inlet (Filter)
7 Exhaust pipe adapter
8 Flexible exhaust pipe
9 Water outlet
10 POWER button
11 TEMP + button
12 TEMP − button
13 IR receiver for remote control
14 Display
15 MODE button
16 SPEED button
17 TIMER button
18 LED WATER FULL
Supplied parts
1 Air conditioning unit
1 Remote control
2 Batteries
1 Flexible exhaust pipe
1 Exhaust pipe adapter (Connection on the appliance)
1 Window kit, 3-piece
1 Water hose, Ø 10 mm
2 Rubber caps (spares)
2 Plugs (spares)
Unpacking the appliance
1. Remove the appliance from its packaging.
2. Remove all the packaging material such as plastic bags, fi ller material,
cable ties and cardboard packaging.
3. Check that all parts are supplied in the package.
30
CL3639_IM
Notes on use
CAUTION: Important for initial operation or after transport!
Before initial operation, the unit must stay in an upright position for at
least 3 hours in order for the cooling agent to sink. The compressor will
be damaged otherwise.
CAUTION:
When you interrupt the operation with the POWER button, wait for at
least 3 minutes before switching the appliance on again.
NOTE:
You will fi nd all operating buttons on both the unit and the remote con-
trol. Same buttons represent the same functions.
• The appliance operates most effectively with a room size up to 70 m³.
• The fl exible exhaust hose and the adapter (7) have been manufactured
especially for this appliance. In order to avoid incorrect operation, do not
replace the pipe with another pipe.
• The exhaust pipe can be extended up to 150 cm. Do not use any
extension.
• Ensure free airfl ow. Make sure not to kink or bend the exhaust pipe. Any
blockage can cause the unit to overheat.
• Close all windows and doors in order to prevent outside air from enter-
ing the room and thus allowing a more effective operation of the device.
Initial operation
Location
• When installing the device, make sure to keep a distance of at least
30 cm between the unit and any walls or other objects.
• The surface must be fl at and dry.
Assembly of exhaust pipe
NOTE:
For sliding windows, you may use the window kit provided and install it
in a vertical or horizontal position. Adjust the length of the seal plate as
desired.
1. Turn the adapter (7) to one end of the exhaust pipe.
2. Connect the exhaust pipe to the unit using the exhaust pipe connector.
Set the adapter fi rst on the left side. Press the adapter on the right side
down into the linkage.
3. Extend the pipe to the desired length.
4. Stick the open end of the pipe into a window.
5. Close the window as far as possible. Also lower any external roller
blinds, if present, to the end of the pipe.
Remote control
1. Open the battery compartment cover on the back of the remote
control.
2. Insert 2 batteries of type R03 "AAA" 1.5 V, observing the correct polari-
ty (see markings on the bottom of the compartment)!
3. Close the battery compartment cover.
Mains connection
1. Make sure the mains voltage you want to use corresponds to the volt-
age of the unit. Please check the rating label for detailed specifi cations.
2. Connect the unit to a properly installed grounded socket. A signal will
sound indicating that the unit is ready for use. The display will show the
current room temperature with low illumination.
15.12.2015