Bosch GCM 350-254 Notice Originale page 33

OBJ_BUCH-2953-002.book Page 33 Friday, June 30, 2017 11:46 AM
55 Screws for insert plate
56 Material stop*
57 Lock screw of the material stop*
58 Clamping screw of the material stop*
59 Adjustment screw for laser positioning (right of the saw
blade)
60 Hex key (2,5 mm)
61 Adjustment screw for laser positioning (left of the saw
blade)
62 Screws for laser protection cap
63 Fastening screw for laser mounting plate
64 Fastening screw for laser housing
65 Stop screw for 0° bevel angle
66 Stop screw for left-hand bevel angle range
67 Stop screw for right-hand bevel angle range
68 Set screws of scale 26 for mitre angles
69 Screw for mitre angle indicator
70 Velcro strap
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number 3 601 M22 ...
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Divergence of laser line
Weight according to EPTA-
Procedure 01:2014
Protection class
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Max. cutting width
Mounting hole diameter
Permissible workpiece dimensions (maximum/minimum) see page 37.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
Bosch Power Tools
Noise Information
Sound emission values determined according to
EN 62841-3-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
The noise emission value given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It may also
be used for a preliminary estimation of noise emissions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used for
other applications, with different accessories or is poorly
maintained, the noise emission value may differ. This may sig-
nificantly increase noise emissions over the total working pe-
riod.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually being
used, should also be taken into account. This may significant-
ly reduce noise emissions over the total working period.
... 6..
W 1800
-1
min 3700–5000

nm 650
mW < 0.39
1
1.0 mrad (full angle) 1.0 mrad (full angle) 1.0 mrad (full angle) 1.0 mrad (full angle)
kg 24.2
/II
mm 254
mm 1.7–2.6
mm 3.2
mm 30
– Quick-action clamp 38
– Hex key 37
– Hex key 60
– SDS bolt 30
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
... 640 ... 660
1800 1450
3700–5000 4600

650 650
< 0.39 < 0.39
1
24.2 24.2
/II /II
254 254
1.7–2.6 1.7–2.6
3.2 3.2
25.4 30
1 609 92A 3XP | (30.6.17)
English | 33
GCM 350-254
... 6B0
1800
3700–4600

–
650
< 0.39
1 1
24.2
/II
254
1.7–2.6
3.2
25.4