EINHELL BT-LS 610 Mode D'emploi D'origine page 19

Anleitung_BT_LS_610_610D_SPK1:_
Max. splitting force:
Splitting lift:
Splitting speed
Downwards:
Upwards:
Trunk holding capacity:
Diameter:
Length:
Oil quantity:
Weight:
5. Before starting the equipment
5.1 Fitting the switch/plug combination (Fig. 3)
Install the switch/plug combination on the wood
splitter as shown in Figure 3. Use the four screws
(Fig. 2 / Item 13) for this purpose.
5.2 Fitting the transport handle (Fig. 4/5)
Remove the two screws in the transport handle using
an Allen key (Fig. 4). Place the transport handle over
the two holes in the cover on the rear cover of the
wood splitter and secure it with the two screws as
shown in Figure 5.
5.3 Fitting the wheels (Fig. 6-10)
Push a split pin (Fig. 2 / Item 16) through one of the
holes in the axle (Fig. 2 / Item 14) and bend it as
shown in Figure 6. Now slide a washer (Fig. 2 / Item
15) and a wheel (Fig. 2 / Item 7) over it (Fig. 7).
Guide the axle through the holes provided for it at the
bottom on the rear of the wood splitter (Fig. 8). Now
place the remaining wheel and washer on the axle
(Fig. 9) and secure it with the other split pin (Fig. 10).
5.4 Fitting the control lever and hand guards (Fig
11a-14)
Remove the pre-assembled securing screws from the
two hand guards by undoing the nuts and removing
the screws as shown in Figure 11a. Guide the hand
guards and control level, as shown in Figure 11b,
from the front into the wood splitter so that the ends of
the control lever project through the recesses
provided for it in the control rods (Fig. 12). Then
secure the hand guards using the previously
unassembled securing screws as shown in Figure 13
- 14a.
26.01.2010 14:45 Uhr
6 t 5.5 Fitting the trunk holding plates (Fig. 15a-18)
Undo the star nuts on the two trunk holding plates
480 mm
(Fig. 2/Item 11) by turning these counter-clockwise as
shown in Figure 15a. You now have the trunk holding
plates, star nut A, washer B and fastening screw C
0.032 m/s
(Fig. 15b). Push the trunk holding plates through the
0.12 m/s
guide slots in the hand guards, as shown in Figure 16.
As you do this, ensure that the oval holes in the trunk
holding plates line up with the securing holes. Insert
50 -320 mm
the securing screws A from below through the oval
100 -1040 mm
holes in the trunk holding plates and the holes in the
2.4 l
hand guards as shown in Figure 17 and secure then
by fitting the washers B and star nuts C to them from
99 kg
above (Fig. 18). The trunk holding plates can be
adjusted to the trunk thickness using the oval holes.
5.6 Fitting the chain to adjust the splitter height
(Fig. 19-21)
First undo the lock nut on the chain hook (Fig. 19).
Secure the chain hook to the hole provided for it next
to the chain holder behind the splitter as shown in
Figure 20. The chain is designed to limit the height of
the splitter. To do this, move the splitter
approximately to the required position, switch off the
machine (Fig. 29) and attach the chain in the
appropriate position (Fig. 21).
5.7 Fitting the trunk support (Fig. 22-26)
The trunk support can be installed at three different
heights (Fig. 22):
Position A: Max. log length 520 mm
Position B: Max. log length 770 mm
Position C: Max. log length 1040 mm
There are three attachment devices at different
heights on the wood splitter for this purpose. To use
the trunk support, the locking levers on the
appropriate attachment device must be moved
upwards (Fig. 23) so that they are vertical (Fig. 24).
The trunk support must then be pushed into the
attachment device from the front (Fig. 25) and
secured by returning the locking levers to their
original positions (Fig. 26).
5.8 Filling with hydraulic oil
The wood splitter must be filled with oil before it is
started for the first time. Refer to section 10
"Changing the hydraulic oil"
Seite 19
GB
19