Bosch GWS 10,8-76 V-EC Professional Notice Originale page 18

OBJ_BUCH-2534-002.book Page 18 Tuesday, June 28, 2016 3:48 PM
18 | English
max.
[mm] [mm]
D b
d
76 7
D
b
Selecting Grinding Discs
Grinding discs
Carbide Multi Wheel PVC, wood,
Expert for Metal
Best for Ceramic
Dust/Chip Extraction
 Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Insert the charged battery 4 into the handle until it can be felt
to engage and faces flush against the handle.
Switching On and Off
To start the power tool, push the On/Off switch 3 forwards.
To lock the On/Off switch 3, press the On/Off switch 3 down at
the front until it latches.
To switch off the power tool, release the On/Off switch 3 or, if
it is locked, briefly push down the back of the On/Off switch 3
and then release it.
To save energy, only switch the power tool on when using it.
1 609 92A 3B3 | (28.6.16)
 Check grinding tools before using. The grinding tool
-1
d [min ] [m/s]
Temperature Control/Overload Protection Indicator
10 19.500 80
The red LED indicator 6 will help you in protecting the battery
against overheating and the motor against overloading.
When the LED indicator 6 continuously lights up red, the tem-
perature of the battery is too high and the machine switches off
Material
automatically.
– Switch the power tool off.
composites,
– Allow the battery to cool down before continuing to work.
perspex
The LED indicator 6 flashes red, the power tool is blocked and
Aluminium,
switches off automatically.
copper
– Remove the power tool from the workpiece.
Tile, concrete,
brick
Working Advice
 Exercise caution when cutting slots in structural walls;
 When cutting lightweight materials, take into account
 Clamp the workpiece if it does not remain stationary due
 Do not strain the machine so heavily that it comes to a
 After heavily straining the power tool, continue to run it
 Do not touch grinding and cutting discs before they have
 Do not use the power tool with a cut-off stand.
When the power tool is electrostatically charged, the built-in
electronic control switches it off. To restart the power tool,
press the On/Off switch 3 again.
Rough Grinding
 Never use a cutting disc for roughing.
The best roughing results are achieved when setting the ma-
chine at an angle of 30° to 40°. Move the machine back and
forth with moderate pressure. In this manner, the workpiece
will not become too hot, does not discolour and no grooves are
formed.
Cutting Metal
 For cutting with bonded abrasives, always use the pro-
When cutting, work with moderate feed, adapted to the mate-
rial being cut. Do not exert pressure onto the cutting disc, tilt or
oscillate the machine.
Do not reduce the speed of running down cutting discs by ap-
plying sideward pressure.
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grinding
tools. Damaged grinding tools can burst and cause injuries.
The power tool will continue to work as soon as the blockage
is rectified.
see Section "Information on Structures".
the statutory provisions and recommendations of the
material manufacturer.
to its own weight.
standstill.
at no-load for several minutes to cool down the accesso-
ry.
cooled down. The discs can become very hot while work-
ing.
tection guard for cutting 10.
Bosch Power Tools