Before Starting The Equipment; Assembly - EINHELL TH-TS 1525 U Mode D'emploi D'origine

conclusions as to the need for additional precau-
tions. Factors with a potential infl uence on the ac-
tual immission level at the workplace include the
duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machi-
nes and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
Anl_TH_TS_1525_U_SPK1.indb 25 Anl_TH_TS_1525_U_SPK1.indb 25
GB
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.

6. Assembly

Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
6.1 Assembling the base frame
(Fig. 15/16/17)
•
Turn the saw upside down and place it on the
floor.
•
Use the washers (c) and the hex screws (a) to
fasten the 4 legs (29) loosely to the saw.
•
Now use the hex screws (a), the washers (c)
and the nuts (d) to fasten the longitudinal-
struts (31) and the cross-struts (30) loosely to
the legs. Please note: The longer struts have
to be used on the sides.
•
Finally, tighten all screws and nuts on the
base frame.
•
Screw the additional legs (A) to the rear legs
(29) so that they point towards the rear of the
machine (Fig. 17).
•
Plug the rubber feet (13) onto the legs (29).
6.2 Fitting / removing the saw blade guard
(Fig. 3)
•
Mount the saw blade guard (2) on the splitter
(5) so that the screw fits through the hole (18)
in the splitter.
•
Do not tighten the screw (15) too far – the bla-
de guard must be able to move freely.
•
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
6.3. Setting the splitter (Fig. 3/5/6/7)
•
Important! Pull out the power plug.
•
Set the blade (4) to max. cutting depth, move
to 0° position and lock in place.
•
Remove the saw blade guard (see 6.2).
•
Take out the table insert (6) (see 6.4).
•
Slacken the fixing screw (19).
- 25 -
19.02.13 08:56 19.02.13 08:56