VONROC S2_AG501DC Traduction De La Notice Originale page 10

EN
b) Do not position your body in line with and
behind the rotating wheel. When the wheel, at
the point of operation, is moving away from your
body, the possible kickback may propel the spin-
ning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut­off wheel from the cut while
the wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re­enter the cut. The wheel may bind,
walk up or kickback if the power tool is restar-
ted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick­
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
f) Use extra caution when making a "pocket cut"
into existing walls or other blind areas. The prot-
ruding wheel may cut gas or water pipes, electri-
cal wiring or objects that can cause kickback.
SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of short-circuiting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
c) In case of damage and improper use of the bat­
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e) The battery can be damaged by pointed objects
such as nails or screwdrivers or by force applied
externally. An internal short circuit can occur and
the battery can burn, smoke, explode or overheat.
10
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type rechargea-
ble Battery packs with the charger. Other types of bat-
teries may burst causing personal injury and damage.
a) The appliance is not to be used by persons
(including children) with reduced physical, sen­
sory or mental capabilities, or lack of experien­
ce and knowledge, unless they have been given
supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging non­rechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable
for the power rating of the machine with a
minimum thickness of 1.5 mm
tension cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
Your angle grinder has been designed for grinding
masonry and steel materials without the use of
water. For cutting, a special protection guard
must be used (not included). Fig. F2.
TECHNICAL SPECIFICATIONS
Model No.
Voltage
No load speed
Grinding disc
Diameter:
Bore:
Spindle thread
Weight
Sound pressure level L
PA
Acoustic power level L
WA
Vibration a
h,AG
. If you use a ex-
2
S2_AG501DC
20V
8.000/min
115 mm
22.2 mm
M14
1.55 kg
75.7 dB(A), K=3dB(A)
86.7 dB(A), K=3dB(A)
5.642 m/s , K=1.5 m/s
2 2
WWW.VONROC.COM